Results 51 to 60 of about 612,127 (299)
Analysis of Influence of Sand Matrix on Properties of Moulding Compounds Made with Furan Resin Intended for 3D Printing [PDF]
Archives of Foundry EngineeringBinder jetting (BJ) sand printing is a 3D printing process in which a sand mould or sand core is produced from an STL file. A single layer of a sand matrix consisting of one or more grains in height of sand is applied to a worktable, and then a liquid ...
D.R. Gruszka +3 more
doaj +1 more source
Metals, 2021 This investigation is focused on the corrosion evaluation of an as-cast Al-Si alloy, obtained by two different casting methods: traditional sand casting and three-printing casting, using a binder jetted mold.
María Ángeles Castro-Sastre +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.The results demonstrate a simulation‐driven workflow that applies LSB topology optimization with additive manufacturing constraints to mission‐specific load cases, integrating European Cooperation for Space Standardization compliant verification and manufacturability to develop structurally efficient rover suspension components.
Stelios K. Georgantzinos +11 more
wiley +1 more source
Open Ceramics, 2020 The possibility of creating patient-specific individual implants makes Additive Manufacturing technologies of special interest for the medical sector. For substitution of bone defects, powder based Additive Manufacturing by Binder Jetting is a suitable ...
Fabio Chinellato +4 more
doaj +1 more source
Sistem penilaian kemahiran kejuruteraan awam anjuran Majlis Latihan Vokasional Kebangsaan [PDF]
, 1996 Tujuan kajian ini dibuat adalah untuk mengetahui punca-punca kegagalan pelatih-pelatih dalam menghadapi Peperiksaan Kemahiran Malaysia bagi kursus Kejuruteraan A warn yang dikendalikan oleh Majlis Latihan Vokasional Kebangsaan (MLVK). Pelatih-pelatih ini
Khalid, Kamarudin
core
Influence of an Argon/Silane Atmosphere on the Temperature of a Thermal Plasma
Advanced Engineering Materials, EarlyView.The influence of a silane‐doped argon atmosphere on the chemical composition and temperature of a thermal nontransferring argon plasma is investigated using optical emission spectroscopy. As a result of the high amount of free electrons resulting from the stepwise ionization and dissociation of the silane molecule, even a silane addition of 0.01 vol ...
Lena Kreie +4 more
wiley +1 more source
Virtual and Physical Prototyping, 2023 Additive manufacturing is increasingly utilised in the energy conversion and storage field. It offers great flexibility to fabricate structural materials with improved physical properties, and other advantages such as material waste reduction ...
Qing Liu +4 more
doaj +1 more source
Mechanisms of fragmentation of Al-W granular composites under dynamic loading
, 2012 Numerical simulations of Aluminum (Al) and Tungsten (W) granular composite rings under various dynamic loading conditions caused by explosive loading were examined.
D. J. Benson +3 more
core +1 more source
Conformal Robotic Stereolithography [PDF]
, 2017 Additive manufacturing by layerwise photopolymerization, commonly called stereolithography (SLA), is attractive due to its high resolution and diversity of materials chemistry.
Archer, Chad +9 more
core +1 more source
Multifunctional Microstructured Surfaces by Microcontact Printing of Reactive Microgels
Advanced Functional Materials, EarlyView.Reactive poly(N‐vinylcaprolactam‐co‐glycidyl methacrylate) microgels are used as functional inks to create surface‐grafted arrays on glass via microcontact printing. The patterns (10–50 µm widths and spacings) enable stable binding and post‐functionalization with dyes and peptides.
Inga Litzen +4 more
wiley +1 more source