Results 131 to 140 of about 16,376 (261)

A 3D‐Printed Blister Test Platform for Quantifying Biointerface Adhesion Mechanisms

Advanced Materials Interfaces, EarlyView.
A 3D‐printed blister platform enables energy‐resolved characterization of soft hydrogel–rigid interfaces. Integrating precision pressure control with hyperelastic modeling directly quantifies adhesion energy (G) and R‐curve toughening. Results reveal that modulating hydrogel concentration and surface roughness drives a tunable transition from cohesive ...
Yoontae Kim, Rahul Patil, Argyris K. Lazaris, Xinran Zhang, Stella Alimperti   +4 more
wiley   +1 more source

Rheo-diecasting AZ91D magnesium alloy

, 2007
Magnesium recycling has become more important in today’s environmentally aware society. To prompt the usage of recycled magnesium scrap and further improve casting structure and properties, a novel physical approach, the rheo-diecasting process (RDC ...
Wang, Y, Liu, G, Fan, Z
core  

Enhanced Infection Resistance and Regenerative Healing of Titanium Implants via Peptide‐Loaded Biodegradable Coatings

Advanced Materials Technologies, EarlyView.
This study presents a new biodegradable coating for titanium implants using a natural antimicrobial peptide, caerin 1.9. Applied via solvent casting, the coating offers sustained antibacterial protection and promotes healing. Tested on 3D‐printed porous titanium scaffolds, it effectively prevented infection—including against resistant bacteria—while ...
Hejie Li, Tianfang Wang, Nicolas Soro, Guoying Ni, Meg Allom, D. İpek Kurtböke, Xiaosong Liu, Damon Kent   +7 more
wiley   +1 more source

Oxidation of Aluminium-Magnesium alloys at elevated temperature in the solid, semi-liquid and liquid states

, 1987
This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.Sensitive thermogravimetric equipment was used to monitor the oxidation rates of A1-1 to 9% Mg alloys in 0.21 oxygen/0.79 helium mixtures with and without 0.
Silva, MP, Silva, M.P
core  

Microstructure, mechanical properties and damping behavior of novel Mg-Ga-Zn alloys fabricated by medium-high strain rate rolling

Journal of Magnesium and Alloys
This study examines the grain characteristics, dynamic precipitation phase characteristics, and texture evolution of Mg-Ga-xZn alloys produced through medium-high strain rate rolling.
Wensen Huang, Jihua Chen, Hongge Yan, Weijun Xia, Fei Zhao   +4 more
doaj   +1 more source

End‐to‐End Sensing Systems for Breast Cancer: From Wearables for Early Detection to Lab‐Based Diagnosis Chips

Advanced Materials Technologies, EarlyView.
This review explores advances in wearable and lab‐on‐chip technologies for breast cancer detection. Covering tactile, thermal, ultrasound, microwave, electrical impedance tomography, electrochemical, microelectromechanical, and optical systems, it highlights innovations in flexible electronics, nanomaterials, and machine learning.
Neshika Wijewardhane, Lyn I. Jones, Richard M. Martin, Helen Winter, Faezeh Arab Hassani   +4 more
wiley   +1 more source

CORROSION BEHAVIOUR OF THE AZ31 MAGNESIUM ALLOY AND SURFACE TREATMENTS FOR ITS CORROSION PROTECTION

, 2009
Nowadays environmental conservation forces the transportation industry to manufacture lighter and low emissions transport vehicles. In this contest, magnesium alloys have found increasing attention by the automotive industry because of their low density ...
Zanotto, Federica
core  

Large‐Scale and Cost‐Effective Fabrication of Ultra‐Thin, Biodegradable Microelectrode Arrays and Pressure Sensors Using Laser Micromachining

Advanced Materials Technologies, EarlyView.
A mask‐free and cost‐effective UV‐pico‐second laser‐based microfabrication method is proposed to fabricate large‐area biodegradable microelectrode arrays and pressure sensors. These devices demonstrate low impedance, good conformability, excellent biocompatibility, and rapid degradation, providing a new route for next‐generation transient electronics ...
Bhavani Prasad Yalagala, Asfand Tanwear, María Cerezo‐Sánchez, Hossein Parvizi, Morteza Amjadi, Hadi Heidari   +5 more
wiley   +1 more source

Strength modelling of Al-Cu-Mg Type alloys

, 2006
Age hardening of Al-Cu-Mg type alloys occurs in two stages separated by a constant hardness plateau when the alloys are aged at 110°C to 240?C after solution treatment and quenching.
Yan, Jialin
core  

Unlocking the Potential of MXene‐Based Electrochemical Biosensors: A Review of Biofunctionalization Strategies and Biosensing Principles

Advanced Materials Technologies, EarlyView.
ABSTRACT Electrochemical biosensors enable the accurate and timely detection of clinical biomarkers, improving healthcare and precision medicine. MXene nanosheets, a class of 2D transition metal carbides, nitrides, and carbonitrides, are promising materials for developing next‐generation electrochemical biosensors due to their unique physicochemical ...
Muhsin Ali, Sharat Chandra Barman, Isobel Steer, Aya H. Alshareef, Dana Alsulaiman   +4 more
wiley   +1 more source