Results 291 to 300 of about 1,742,691 (356)
Some of the next articles are maybe not open access.
Bipolar plates for PEM fuel cells
Journal of Power Sources, 2003Abstract The bipolar plates are in weight and volume the major part of the PEM fuel cell stack, and are also a significant contributor to the stack costs. The bipolar plate is therefore a key component if power density has to increase and costs must come down.
E Middelman +4 more
openaire +1 more source
International journal of hydrogen energy, 2019
Conductive polymer composite (CPC) materials are extensively used for the bipolar plate in Polymer Electrolyte Membrane Fuel Cells (PEMFCs). The produced CPC materials through the extrusion process strongly relate to electrical conductivity and ...
Nabilah Afiqah Mohd Radzuan +7 more
semanticscholar +1 more source
Conductive polymer composite (CPC) materials are extensively used for the bipolar plate in Polymer Electrolyte Membrane Fuel Cells (PEMFCs). The produced CPC materials through the extrusion process strongly relate to electrical conductivity and ...
Nabilah Afiqah Mohd Radzuan +7 more
semanticscholar +1 more source
, 2020
Stainless steels, due to their scalability, formability, and cost effectiveness, are, today, used as bipolar plates in proton-exchange membrane fuel cells (PEMFCs).
Xuejie Li +6 more
semanticscholar +1 more source
Stainless steels, due to their scalability, formability, and cost effectiveness, are, today, used as bipolar plates in proton-exchange membrane fuel cells (PEMFCs).
Xuejie Li +6 more
semanticscholar +1 more source
Journal of Alloys and Compounds, 2019
Graphite-like carbon films are deposited on 304SS substrates with different duty cycles and bias voltages by unbalanced magnetron sputtering, both the alternating current (AC) twinned and direct current (DC) single graphite targets are used.
R. Hu +4 more
semanticscholar +1 more source
Graphite-like carbon films are deposited on 304SS substrates with different duty cycles and bias voltages by unbalanced magnetron sputtering, both the alternating current (AC) twinned and direct current (DC) single graphite targets are used.
R. Hu +4 more
semanticscholar +1 more source
, 2020
The corrosion properties of AISI316L stainless steel (316 L SS) as bipolar plates are investigated under aqueous acid methanol solutions (0.05 M H2SO4 + 2 ppm HF + 10 M HCOOH + x M CH3OH (x = 0, 3, 6 and 9) solutions at 70 °C) to simulate the varied ...
Haibang Zhang +3 more
semanticscholar +1 more source
The corrosion properties of AISI316L stainless steel (316 L SS) as bipolar plates are investigated under aqueous acid methanol solutions (0.05 M H2SO4 + 2 ppm HF + 10 M HCOOH + x M CH3OH (x = 0, 3, 6 and 9) solutions at 70 °C) to simulate the varied ...
Haibang Zhang +3 more
semanticscholar +1 more source
A review of proton exchange membrane fuel cell's bipolar plate design and fabrication process
Journal of Power Sources, 2022Qingshan Liu +4 more
semanticscholar +1 more source
Experimental analysis of PEM fuel cell performance using lung channel design bipolar plate
International Journal of Green Energy, 2019Performance of a polymer electrolyte membrane fuel cell is appreciably improved by flow-field geometry. In recent literature, it has been observed that naturally inspired flow channel designs enhance the fuel-cell performance.
Srinivasa Reddy Badduri +2 more
semanticscholar +1 more source
Fuel Cells, 2019
The drawback of corrosion resistance and surface conductivity are two obvious defects to limit the large‐scale application of 316L stainless steel (316L SS) as bipolar plate (BP) in proton exchange membrane fuel cell (PEMFC).
T. Li +6 more
semanticscholar +1 more source
The drawback of corrosion resistance and surface conductivity are two obvious defects to limit the large‐scale application of 316L stainless steel (316L SS) as bipolar plate (BP) in proton exchange membrane fuel cell (PEMFC).
T. Li +6 more
semanticscholar +1 more source

