Results 181 to 190 of about 9,000,208 (326)
Microscopy Research and Technique, EarlyView.This study demonstrates that Biodentine XP exhibits superior cytocompatibility, promotes odontogenic differentiation, and enhances mineralization in human dental pulp stem cells, supporting its use in regenerative endodontics. Resin‐modified materials showed lower bioactivity, highlighting the importance of material composition in pulp therapy outcomes.
Francisco Javier Rodríguez‐Lozano +5 more
wiley +1 more source
Advancements in 3D Printing of Self‐Healing Polymer Systems
Macromolecular Materials and Engineering, EarlyView.This review provides an overview of the most common 3D printing technologies and summarizes the numerous methods to produce self‐healing materials. The challenges and strategies used to adapt these methods to 3D printing are then highlighted to provide a framework for future research in 3D printing self‐healing polymer systems.
Adam L. Bachmann, Bryan S. Beckingham
wiley +1 more source
Macromolecular Materials and Engineering, EarlyView.Two novel bio‐based epoxy monomers, diglycidyl‐4‐allylphenol (DG‐4A) and triglycidyl‐diallylphenol (TG‐DA), derived from estragole (92% and 72% bio‐content), were synthesized and cured with isophorone diamin (IPDA) and 4,4´‐diaminodiphenyl sulfone (DDS). The resins show high Tgs, with DG‐4A reaching and TG‐DA exceeding DGEBA‐based systems. These resins
Florian Bauer +4 more
wiley +1 more source
Nano Select, EarlyView.Multifunctional structural battery composites can store electrical energy while bearing mechanical loads, thereby reducing parasitic mass and volume. We present a novel solid‐state PETEA‐based electrolyte, which can be cured in situ after infiltration into the reinforcement fibers in its monomer form.
Daniel Vogt +4 more
wiley +1 more source
Sustainable Carbon Fiber Composites Based on Recyclable Bio‐Based Vanillin Thermoset Polymers
Polymer Composites, EarlyView.Development of composite materials made from a bio‐based and mechanically recycled vitrimeric polymer matrix. ABSTRACT Although bisphenol A (BPA) is the most used organic compound in the production of thermosets for composite materials, there has been an urgent scientific concern to eliminate it in the last years due to the environmental issues raised ...
Javier Gómez Sánchez +4 more
wiley +1 more source
Prediction of Cure‐Induced Wrinkles Aimed at the Manufacturing of Large Wind Turbine Blades
Polymer Composites, EarlyView.The step‐wise progression of the development of cure‐induced wrinkles. Before curing, at room temperature the laminate is resting at the mould face. In the next step, the wrinkle is developing due to thermal gradients. At the end of curing, the composite has cooled down and the undulation is left in, byt the increase in resin stiffness across the ...
Jesper K. Jørgensen +2 more
wiley +1 more source
Synthesis of perfluoroalkylene aromatic diamines [PDF]
Analogues of methylene dianilines were synthesized, in which the methylene group between the two aromatic nuclei was replaced by various perfluoroalkylene linkage.
Ito, T. I. +3 more
core +1 more source
Journal of Polymer Science, EarlyView.Tandem mechanochemical‐sonochemical for the strategic synthesis for 2,4,6‐trisubstituted derivatives of perfluoropyridine as bio‐based prepolymer materials. ABSTRACT Substitution of perfluoropyridine (PFP) in the 4‐position through an SNAr reaction is facile through mechanochemical methods, with yields in excess of 99% and short reaction times on a ...
Jason Pulfer +5 more
wiley +1 more source