Results 51 to 60 of about 116,113 (207)
Impact of rapid-hardening cements on mechanical properties of cement bitumen emulsion asphalt
, 2016 Cement bitumen emulsion asphalt (CBEA) is obtained by mixing bitumen emulsion, cement, aggregates and filler at ambient temperature. CBEA is thought to be a promising substitute for hot mix asphalt because of its low environmental impact and cost ...
Partl, Manfred N. +5 more
core +1 more source
Battery Energy, Volume 5, Issue 3, May 2026.Advanced activated carbons with high capacitance for supercapacitors and substantial hydrogen storage, underscoring their promise for multifunctional energy systems. ABSTRACT Activated carbon (AC) materials, characterized by their high surface area, diverse pore structure, and excellent electrical conductivity, have proven to be highly efficient and ...
Monjur Mourshed +3 more
wiley +1 more source
The Baltic Journal of Road and Bridge Engineering, 2016 This paper presents findings of a study concerning the influence of binder type on the mechanical properties of road base in the cold recycling technology.
Marek Iwański, Anna Chomicz-Kowalska
doaj +1 more source
The Canadian Journal of Chemical Engineering, Volume 104, Issue 4, Page 2020-2032, April 2026.25 g of oil sands extracted by dynamic accelerated solvent extraction, yielding 177 mL of bitumen–toluene extract and clean dried solids in approximately 12 min. Abstract Determining the oil, water, and solids (OWS) contents of oil sand is essential to many aspects of the oil sands industry including mine planning, optimization of extraction processes,
Ceanna Ting‐Yan Cheung +1 more
wiley +1 more source
Engineering Reports, Volume 8, Issue 4, April 2026.A novel multiphase composite was developed to prevent premature failure of waterproofing layers in pig houses. The system, comprising polyurethane, asphalt, and calcium carbonate, achieves a 1.35 MPa bonding strength and resists corrosion via a synergistic crosslinking, buffering, and passivation mechanism.
Dong Yan +8 more
wiley +1 more source
PROBLEMS AND PROSPECTS OF PETROLEUM BITUMEN PRODUCTION
Вестник Дагестанского государственного технического университета: Технические науки, 2016 . The world production petroleum bitumen for road construction is considered. The problems and prospects of the bitumen production in the world and Russia are shown.At present leading positions on Russian bitumen market occupy the companies Gazprom Oil ...
N. A. Belova +2 more
doaj +1 more source
Experimental methods in chemical engineering: Electrospinning
The Canadian Journal of Chemical Engineering, Volume 104, Issue 2, Page 556-568, February 2026.Abstract Electrospinning produces micro‐ and nanofibres by forcing a polymeric solution through a fine needle in an electric field that produces a filament that accumulates onto a collector plate. The fibre morphology depends on solution properties, distance between needle and plate, feed rate, and electric field intensity.
M. Olga Guerrero‐Pérez +2 more
wiley +1 more source
Development of Cold In-Place Recycling with Bitumen Emulsion and Biomass Bottom Ash
Crystals, 2021 Power generation from biomass is one of the most promising energy sources available today. However, this industry has a series of wastes derived from its activity, mainly biomass fly ash and biomass bottom ash.
Jorge Suárez-Macías +3 more
doaj +1 more source
Advances in Civil Engineering, Volume 2026, Issue 1, 2026.Assessing pavement sustainability requires jointly evaluating structural performance and environmental impacts, yet these dimensions are often analyzed separately. This study proposes an integrated framework combining mechanistic–empirical pavement design and life cycle assessment (LCA) to quantify the structural–environmental trade‐off associated with
Alexandre Simas de Medeiros +3 more
wiley +1 more source
Laboratory Performance Evaluation of CIR-Emulsion and it Comparison Against CIR-Form Test Result from Phase II, Final Report TR-578 Phase III, December 2009 [PDF]
, 2009 Currently, no standard mix design procedure is available for CIR-emulsion in Iowa. The CIR-foam mix design process developed during the previous phase is applied for CIR-emulsion mixtures with varying emulsified asphalt contents.
core