Results 221 to 230 of about 102,556 (307)

First 20 Years of Orbitrap Mass Spectrometry as the Mainstream Analytical Technique

Mass Spectrometry Reviews, EarlyView.
ABSTRACT This review traces the first 20 years of Orbitrap mass spectrometry as a mainstream high‑resolution and accurate‑mass (HR/AM) technology. It outlines the historical development of the Orbitrap analyzer, the evolution of major instrument families, and the key technological innovations that enabled its widespread adoption. Particular emphasis is
Alexander Makarov
wiley   +1 more source

Fabrication of Sustainable Diatomite-Based Foams with a Micro-Macroporous Synergistic Structure. [PDF]

Materials (Basel)
Ning H, Li Z, Liu N, Li C, Lu Y, Li L.
europepmc   +1 more source

Random Chemostats with Competition and Different Kinetics to Investigate the Growth of the Gut Microbiome

Mathematical Methods in the Applied Sciences, EarlyView.
ABSTRACT We investigate some chemostat models incorporating wall growth, competition, random fluctuations on the dilution rate, and different consumption functions (Monod and Haldane). We analyze the asymptotic behavior of the solutions of the corresponding random differential systems to establish conditions on the model parameters under which the ...
Javier López‐de‐la‐Cruz, Felipe Rivero, Carlos R. Takaessu Jr.   +2 more
wiley   +1 more source

Influence of Wood Chemical Composition on Liquefaction Efficiency and Polyurethane Foam Properties: A Study of Red Angico and Mahogany. [PDF]

Materials (Basel)
Silva E, Cruz-Lopes L, Domingos I, Gonçalves F, Cruz BDS, Fassarella M, Almeida AT, Esteves B.   +7 more
europepmc   +1 more source

Development of Vertical Wind Turbine Blades Using 4D Printing of Composites

Polymer Composites, EarlyView.
Vertical axis wind turbine: White blade: Commercial. Black blade: Composite. ABSTRACT This paper presents the procedure to make vertical wind turbine blades using the technique of 4D printing of composites (4DPC). The blades are made using carbon/epoxy composite materials with a fiber volume fraction of about 60%.
Emad Fakhimi, Suong Van Hoa
wiley   +1 more source

On the Evaluation of Flow Properties Characterizing Blown Film Extrusion of Polyolefin Alternatives. [PDF]

Polymers (Basel)
Filip P, Hausnerova B, Endlerova D, Möginger B, Azevedo J.   +4 more
europepmc   +1 more source

On the Mechanical and Thermal Behavior of PLA, PBAT, and PHBV‐Based Ternary Blends and the Effect of Short Flax Fibers as Reinforcing Agents

Polymer Composites, EarlyView.
Preparation and testing of biodegradable polymer ternary blends and composites with short flax fibres. ABSTRACT Bioplastics offer environmental benefits but they are costly and exhibit lower mechanical and thermal performance compared to fossil‐based counterparts. Poly(butylene adipate‐co‐terephthalate) (PBAT) exhibits high ductility but relatively low
Alessia Pantaleoni, Irene Bavasso, Maria Paola Bracciale, Claudia Sergi, Pietro Russo, Jacopo Tirillò, Fabrizio Sarasini   +6 more
wiley   +1 more source

Unexpected Primary Spontaneous Pneumothorax in a Non-smoking Patient After Blowing Out Birthday Candles. [PDF]

Cureus
Laouar L, Dammene Debbih N.
europepmc   +1 more source

Overcoming Challenges in 3D Printing of Polyolefins and Their Composites: A Review on Strategies for Improved Printability and Performance

Polymer Engineering &Science, EarlyView.
This review integrates the molecular fundamentals, key challenges, and mitigation strategies in polyolefin 3D printing, focusing on shrinkage, warpage, and adhesion control. It highlights material design approaches using recycled polyolefins and functional fillers to improve printability, mechanical properties, and sustainability in additive ...
Malik Hassan, Philip McMorran, Marwan Eid, Julia Blair, Amar K. Mohanty, Manjusri Misra   +5 more
wiley   +1 more source

Cellular Structure Optimization in Microwave-Assisted Foaming of Acrylated Epoxidized Soybean Oil. [PDF]

ACS Omega
Vignali A, Bertini F, Iannace S.
europepmc   +1 more source