Results 101 to 110 of about 542,358 (362)
Modification of as-cast Al-Mg/B4C composite by addition of Zr [PDF]
, 2016 Zirconium was used in Al-Mg/B4C composite to improve compocasting efficiency by increasing particle incorporation. Scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS) results revealed that by addition of zirconium a reaction
Bahremand, M. R. +4 more
core +2 more sources
Direct Consolidation of Copper–Graphene Composite by Rotary Swaging
Advanced Engineering Materials, EarlyView.The applicability of the rotary swaging method for preparation of electroconductive copper–graphene composite by direct consolidation of powders is proven. The consolidated material features advantageous microstructure featuring fine grains and twins, with homogeneous distribution of graphene, primarily along the twin boundaries, which contribute to ...
Radim Kocich +2 more
wiley +1 more source
Microshear bond strength of conventional and self-adhesive resin cements to feldsphatic ceramic
Brazilian Journal of Oral Sciences, 2018 Aim: The aim of this study was to verify the microshear bond strength of conventional and self-adhesive resin cements to feldsphatic ceramic. Methods: Twenty discs of Starlight ceramic (Degudent) were made (15mm x 2mm).
Estéfani Maminis Soares Couto +5 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study investigates the mechanical properties of Carbon/Aramid intraply hybrid fiber‐reinforced Elium composites under 6 months of water aging. After aging, flexural strength decreases by 25.89%, tensile strength by 4.40%, and fracture toughness by 21.56%.
Muhammed Huseyin Guzel, Gurol Onal
wiley +1 more source
Chinese Journal of Mechanical EngineeringIt is difficult to effectively improve the low bonding strength of TA1/304 clad plates. This study proposes a new process for applying pulse current (1500 A, 500 Hz, 50% duty cycle) to TA1/304 clad plates during the rolling process, which changes the ...
Xiongwei Guo +7 more
doaj +1 more source
From Nature to Engineering: Mortar Volume and Interfacial Mechanics in Bioinspired Ceramics
Advanced Engineering Materials, EarlyView.Inspired by natural armors like nacre, this study explores how varying the volume fraction of the soft mortar layer impacts the interfacial strength and toughness of bioinspired ceramics. Experimental and computational analysis reveals that higher mortar volumes increase energy dissipation but reduce interfacial stiffness, offering insights for ...
Ehsan Azad +4 more
wiley +1 more source
BuildingsThe interlayer bonding strength between a cement-stabilized macadam (CSM) base and an asphalt surface layer significantly influences asphalt pavement performance.
Weijun Guo +4 more
doaj +1 more source
Characterization of dentine to assess bond strength of dental composites [PDF]
, 2015 This study was performed to develop alternating dentine adhesion models that could help in the evaluation of a self-bonding dental composite. For this purpose dentine from human and ivory was characterized chemically and microscopically before and after ...
Aljabo, A +6 more
core +2 more sources
Graphene–Catechol Dental Sealant: Antibacterial and Mechanical Evaluation
Advanced Engineering Materials, EarlyView.This study presents dental sealants made with graphene and L‐DOPA‐modified graphene. L‐DOPA enhances graphene dispersion, improving sealant properties. The material shows antibacterial activity against S. mutans and L. casei, along with high strength and elasticity.
Renata Pereira +6 more
wiley +1 more source
A Novel Process for Joining Ti Alloy and Al Alloy using Two-Stage Sintering Powder Metallurgy
High Temperature Materials and Processes, 2018 The major challenges for conventional diffusion bonding of joining Ti alloy and Al alloy are the undesirable interfacial reaction, low matrixes and joint strength.
Long Luping +4 more
doaj +1 more source