Results 71 to 80 of about 22,818 (313)

Impact of converter interface type on the protection requirements for DC aircraft power systems

, 2012
The utilization of converter interfaces has the potential to significantly alter the protection system design requirements in future aircraft platforms.
Burt, Graeme, Norman, Patrick, Galloway, Stuart, Fletcher, Steven   +3 more
core   +1 more source

Circuit Simulation for Solar Power Maximum Power Point Tracking with Different Buck-Boost Converter Topologies [PDF]

, 2014
The power converter is one of the essential elements for effective use of renewable power sources. This paper focuses on the development of a circuit simulation model for maximum power point tracking (MPPT) evaluation of solar power that involves using ...
Bo-Chih Chen, 蕭照焜; 李珉毅; 魏煜宸; 陳柏志, 蕭照焜, Yu-Chen Wei, 蕭照焜;李珉毅;魏煜宸;陳柏志, Jaw-Kuen Shiau, Min-Yi Lee   +6 more
core   +1 more source

Composition‐Tuned Enhancement of the Anomalous Nernst Effect in FeCo–Pt Thin Films on Rigid and Flexible Substrates

Advanced Engineering Materials, EarlyView.
Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi, Hiroyuki Awano, Kenji Tanabe   +2 more
wiley   +1 more source

Analysis of Non-minimum Phase in Buck-Boost Converter

MATEC Web of Conferences, 2016
In this paper, relations among the parameters of the non-minimum phase for the Buck-Boost converter are studied. It is demonstrated that when the Buck-Boost converter works in Buck mode, the negative regulation voltage is determined by the converter with
Huang Jinfeng, Liu Shulin
doaj   +1 more source

Evaluating Energy Absorption Performance of Filled Lattice Structures

Advanced Engineering Materials, EarlyView.
Maximum stress must be considered to robustly evaluate energy absorber designs. This approach was applied to compare all types of absorbers in a single Ashby diagram and determine the utility of filling lattice voids with a second material. High‐performance fillers can improve the performance of lattices that are limited by buckling or catastrophic ...
Christian Bonney, William P. King, Iwona Jasiuk   +2 more
wiley   +1 more source

Buck-boost converter Fed nine level cascaded H-bridge inverter

This research investigates on simulation of a traditional cascaded H-bridge (CHB) five-level inverter and proposes a nine-level cascaded H-bridge inverter system. The performance of both five-level and nine-level inverter systems is evaluated by modeling
Babu, R. Samuel Rajesh, Devendiren, Shobana, Ramamurthi, Subbulakshmy   +2 more
core   +1 more source

Field Report from Collaborative Research Center 1625: Heterogeneous Research Data Management Using Ontology Representations

Advanced Engineering Materials, EarlyView.
A unified research data management framework for heterogeneous materials data is presented. The system integrates multimodal datasets using ontologies and knowledge graphs, enabling interoperability and FAIR (findable, accessible, interoperable, reusable) data principles. By linking data across scales and workflows, it supports reproducible, Artifitial
Doaa Mohamed, Samuel García Vázquez, Behnam Mardani, Victor Dudarev, Alfred Ludwig, Maribel Acosta, Markus Stricker   +6 more
wiley   +1 more source

Bidirectional positive buck-boost converter

, 2008
In a positive buck-boost (PBB) converter, inductor current and capacitor voltage can be decoupled which may improve system stability. In fact for a specific level of capacitor voltage, the inductor current can be adjusted at different levels and can be ...
Firuz Zare, Zare, Firuz, Arash A. Boora, zare, F., Ledwich, G., A. Boora, Arash, Boora, Arash A., Ghosh, Arindam, Gerard Ledwich, Arindam Ghosh, Ledwich, Gerard F., Ledwich, Gerard, Boora, A.   +12 more
core   +1 more source

Hybrid control of the boost converter: Robust global stabilization [PDF]

52nd IEEE Conference on Decision and Control, 2013
In this paper we consider the modeling and (robust) control of a DC-DC boost converter. In particular, we derive a mathematical model consisting of a constrained switched differential inclusion that includes all possible modes of operation of the converter.
Thomas A. F. Theunisse, Jun Chai, Ricardo G. Sanfelice, W. P. M. H. Heemels   +3 more
openaire   +3 more sources

Fostering Innovation: Streamlining Magnetocaloric Materials Research by Digitalization

Advanced Engineering Materials, EarlyView.
Magnetocaloric cooling (MCE) is an environmentally friendly refrigeration method with great potential. Optimizing MCE materials involves the preparation and screening of large quantities of samples, which in turn generates a large amount of data. A digitalization approach is presented that uses ontologies, knowledge graphs, and digital workflows to ...
Simon Bekemeier, Moritz Blum, Luana Caron, Alisa Chirkova, Philipp Cimiano, Basil Ell, Inga Ennen, Michael Feige, Maik Gaerner, Thomas Hilbig, Andreas Hütten, Günter Reiss, Tapas Samanta, Sonja Schöning, Christian Schröder, Lennart Schwan, Chris Taake, Martin Wortmann   +17 more
wiley   +1 more source