Results 31 to 40 of about 5,825 (220)
Effect of pack-boriding on the tribological behavior of Hardox 450 and HiTuf Steels
Reviews on Advanced Materials Science, 2020 In this study, Hardox 450 and HiTuf steels were boronized by pack-boriding method at 800, 900, and 1000∘C for 5 h. The phases, microstructure, hardness, and wear behavior of boride layers formed on the surface of samples were investigated using XRD, SEM,
Aktaş Bülent +3 more
doaj +1 more source
Development of Innovative Method of Steel Surface Hardening by a Combined Chemical-thermal Treatment [PDF]
, 2016 The aim of the article is a hardening of the surface steel layers due to the combination treatment. Samples of steel 38Cr2MoAl were hardened by complex chemical and thermal treatment such as carburizing and subsequent boriding.
Kostyk, K. (Kateryna)
core
Thermal conductivity of PrRh4.8B2, a layered boride compound [PDF]
APL Materials, 2017 Transmission electron microscopy (TEM), specific heat, and thermal conductivity measurements were carried out for PrRh4.8B2 single crystals. PrRh4.8B2 takes an interesting layered crystal structure, where PrRh3B2 blocks are separated by metal Rh honeycomb layers. The existence of the Rh layers enhances the ferrimagnetic transition temperature.
Yohei Kakefuda +8 more
openaire +2 more sources
Sol–Gel Derived Polymer Precursors for Stereolithography of ZrC
Advanced Engineering Materials, EarlyView.ZrC is a critical material target for extreme temperature conditions. This report describes a protocol for preparing ZrC ceramics via stereolithography and examines the impact of the polymer matrix on carbothermal reduction and mechanical stability of 3D printed ZrC.
Charles J. Rafalko +2 more
wiley +1 more source
Overview of diffusion boriding problems in industrial applications
Zaštita Materijala, 2019 In this paper is systematized a review of the problem which occur during the execution of the boriding process, and which by its occurrence limit its wider and versatile industrial application.
Željko Stojanović, Sanja Stanisavljev
doaj +1 more source
Microstructural alteration and oxidation behavior of boronized stainless steel AISI 440C after heat treatments [PDF]
Songklanakarin Journal of Science and Technology (SJST), 2019 The martensitic stainless steel AISI 440C was boronized at a temperature of 950 °C for about 4 hr. Heat treatments at a temperature of 850 °C for about 2-8 hr were performed to eliminate the FeB phase of the boride layer.
Patcharin Naemchanthara +1 more
doaj +1 more source
Probing the Synthesis of Two-Dimensional Boron by First-Principles Computations
, 2013 Boron synthesis, in theory: Although two-dimensional boron sheets have attracted considerable interest because of their theoretically predicted properties, synthesis of such sheets remains a challenge.
Liu, Yuanyue +2 more
core +1 more source
Advanced Energy Materials, EarlyView.The borate‐based cobalt‐iron catalyst promotes selective oxidation of water rather than chlorine evolution reaction during electrolysis of seawater. When integrated into a zero‐gap electrolyzer prototype, this catalyst supports robust splitting of artificial seawater into oxygen and hydrogen on an extended timescale.
Ananta R. Fareza +10 more
wiley +1 more source
Journal of Materials Research and TechnologyThe fracture behavior of the hot isostatic pressing (HIP) diffusion bonded Ni60A hardfacing layer was evaluated by macro-indentation and uniaxial tensile methods.
Lei Yu +7 more
doaj +1 more source
, 2015 Based on a theoretical study, we demonstrated that magnesium boride nanotubes can reach the same stability as bulk MgB2 structure. However, most stable nanotubular forms are not structurally derived from mixed triangular-hexagonal structural motifs of a ...
Banacky, P. +3 more
core +1 more source