Results 231 to 240 of about 23,409 (291)

Machine Learning‐Supported Analysis for Predicting and Visualizing Nonlinear Relationships Between Material Properties in Electroplated Chromium Layers

Advanced Engineering Materials, EarlyView.
This study applies machine learning regression to predict chromium layer thickness in decorative trivalent chromium electroplating, using 441 experiments from laboratory‐scale (1L) and pilot‐scale (14L) setups. Tree‐based models, particularly CatBoost, outperformed linear regression by capturing nonlinear parameter interactions (R2$R^2$ up to 0.77 ...
Christoph Baumer, Christopher Mai, Luca Eisentraut, Andreas Bund, Ricardo Buettner   +4 more
wiley   +1 more source

The finite element neural network method to simulate two dimensional partial differential equations and perform parameter identification. [PDF]

Sci Rep
Abda M, Berthet L, Hamedi M, Hibatullah D, Piollet E, Blake C, Blais B, Gosselin FP.   +7 more
europepmc   +1 more source

Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading

Advanced Engineering Materials, EarlyView.
This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev, Noah‐Lean Roschlaub, Anne Jung   +2 more
wiley   +1 more source

Analytically grounded full-wave methods for advances in computational electromagnetics. [PDF]

Philos Trans A Math Phys Eng Sci
Lucido M, Kobayashi K, Nosich AI, Pérez Arancibia C, Vukovic A.   +4 more
europepmc   +1 more source

Influence of Si Content and Milling Duration on the Microstructure and Mechanical–Tribological Properties of AlCoCrFeNiSi High‐Entropy Alloys

Advanced Engineering Materials, EarlyView.
Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş, Mehmet Emin Demir, Sercan Özpınar   +2 more
wiley   +1 more source

Mesh variational r-adaptivity for sharp modeling of brittle fracture

Dony G, Moës N, Remacle J.
europepmc   +1 more source

Robust slice-level stroke classification in non-contrast head CT via structural consistency regularization and counterfactual suppression. [PDF]

Front Bioeng Biotechnol
Xu D, Yao Q, Qian L.
europepmc   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Existence of variational solutions to doubly nonlinear systems in nondecreasing domains. [PDF]

J Evol Equ
Schätzler L, Scheven C, Siltakoski J, Stanko C.   +3 more
europepmc   +1 more source

An Inverse Problem for a Fractional Space-Time Diffusion Equation with Fractional Boundary Condition. [PDF]

Entropy (Basel)
Brociek R, Wajda A, Napoli C, Capizzi G, Słota D.   +4 more
europepmc   +1 more source