Extraction of anthocyanins and total phenolic compounds from açai (euterpe oleracea mart.) using an experimental design methodology. part 1: Pressurized liquid extraction [PDF]
, 2020 Currently, açai is one of the most important fruits present in the world. Several studies have demonstrated its high content in phenolic compounds and anthocyanins.
Aliaño González, María José +7 more
core +1 more source
Response-surface-model-based system sizing for nearly/net zero energy buildings under uncertainty [PDF]
, 2018 Properly treating uncertainty is critical for robust system sizing of nearly/net zero energy buildings (ZEBs). To treat uncertainty, the conventional method conducts Monte Carlo simulations for thousands of possible design options, which inevitably leads
Cheng, Y +5 more
core +2 more sources
Extraction of Anthocyanins and Total Phenolic Compounds from Acai (Euterpe oleracea Mart.) Using an Experimental Design Methodology. Part 2: Ultrasound-Assisted Extraction [PDF]
, 2020 Two optimized methods for ultrasound-assisted extraction were evaluated for the extraction of two types of acai bioactive compounds: Total anthocyanins (TAs) and total phenolic compounds (TPCs).
Aliaño González, María José +7 more
core +1 more source
Liquid-phase hydrogenation of bio-refined succinic acid to 1,4-butanediol using bimetallic catalysts [PDF]
, 2019 open access articleDevelopment of a Crotalaria juncea based biorefinery produce large quantity of waste glycerol after trans-esterification of the juncea seeds.
Baidya, P.K. +3 more
core +7 more sources
Extraction of Anthocyanins and Total Phenolic Compounds from Açai (Euterpe oleracea Mart.) Using an Experimental Design Methodology. Part 3: Microwave-Assisted Extraction [PDF]
, 2020 In this work, two methods based on microwave-assisted extraction techniques for the extraction of both anthocyanins and total phenolic compounds from acai have been developed.
Aliaño González, María José +7 more
core +1 more source
Synthesis and process optimization of electrospun PEEK-sulfonated nanofibers by response surface methodology [PDF]
, 2015 In this study electrospun nanofibers of partially sulfonated polyether ether ketone have been produced as a preliminary step for a possible development of composite proton exchange membranes for fuel cells.
Boaretti, Carlo +3 more
core +2 more sources
Use of response surface methodology (RSM) to optimize pea starch-chitosan novel edible film formulation [PDF]
, 2017 The aim of this study was to develop an optimal formulation for preparation of an edible film from chitosan, pea starch and glycerol using response surface methodology (RSM).
Bowyer, Michael +7 more
core +2 more sources
Effect of laser-welding parameters on the heat input and weld-bead profile [PDF]
, 2005 Laser butt-welding of medium carbon steel was investigated using CW 1.5 kW CO2 laser. The effect of laser power (1.2 - 1.43 kW), welding speed (30 - 70 cm/min) and focal point position (-2.5 - 0 mm) on the heat input and the weld-bead geometry (i.e ...
A.G. Olabi +13 more
core +1 more source
, 2020 Degradation of a Basic Blue 41 dye using Fenton reagent was examined at laboratory scale in batch experiments using Box-Behnken statistical experiment design.
Kiflie, Zebene +2 more
core +2 more sources
Optimization of conventional spinning process parameters by means of numerical simulation and statistical analysis [PDF]
, 2010 Research in sheet metal spinning has increased due to a greater demand, especially in the transportation industries, for parts with very high strength-to-weight ratios with low cost.
Essa, K, Hartley, P
core +1 more source