Results 111 to 120 of about 88,573 (165)
Some of the next articles are maybe not open access.
Optimization of hybrid aluminum/cfrp box beams
International Journal of Mechanical Sciences, 1991Abstract Hybrid structural components in which a principal aluminum structure is reinforced with unidirectional CFRP composite laminates are an effective way to meet the requirements of low weight, high strength and stiffness, relative ease of design and fabrication and good reliability.
Triantafillou, T.C., Kim, P., Meier, U.
openaire +1 more source
Connection of I-beam to box-column by a short stub beam
Journal of Constructional Steel Research, 2016Abstract Box-columns are frequently used in moment resisting frames due to the numerous advantages they offer. Accordingly, bolted extended end-plate moment connections are widely used in steel structures due to their advantages such as easy fabrication and fast erection. However, some problems such as inaccessibility to the inside of box-columns for
Saeed Erfani +2 more
openaire +1 more source
Shear behavior of ferrocement box beams
Cement and Concrete Composites, 1991Abstract The shear behavior of ferrocement box beams has been studied by conducting flexural tests on 15 beam specimens. The major parameters used were amounts of wire mesh reinforcement in webs and in flanges of the beam and shear span to depth ratio, a/h. Test results indicate that cracking and ultimate shear forces increase as wire mesh in webs is
G.J. Al-Sulaimani +2 more
openaire +1 more source
International Journal of Mechanical Sciences, 1978
Stress analysis is carried out for the case where a cantilever box beam is subjected to distributed torque and concentrated torque at the tip. Direct stress σx acting in a cover plate is assumed to be in the form of ∑n σn(x)yn where n is an odd integer and the fundamental equation governing a box beam is introduced, using variational method.
openaire +1 more source
Stress analysis is carried out for the case where a cantilever box beam is subjected to distributed torque and concentrated torque at the tip. Direct stress σx acting in a cover plate is assumed to be in the form of ∑n σn(x)yn where n is an odd integer and the fundamental equation governing a box beam is introduced, using variational method.
openaire +1 more source
Finite Element Beam Analysis of Tapered Thin-Walled Box Beams
Thin-Walled Structures, 2016Abstract This paper presents a one-dimensional finite element analysis of tapered thin-walled box beams under out-of-plane loads and twisting moments by developing new C 0 -continuous tapered higher-order beam elements. While higher-order sectional deformations such as distortion were considered earlier, there was no theoretical or finite ...
Soomin Choi +2 more
exaly +2 more sources
Curved box beam bridge analysis
Computers & Structures, 1976Abstract A finite difference procedure is used to determine the response of a single and multi span curved single box beam bridge with any number of interior diaphragms. The bending and torsional distortions as well as cross-sectional distortions are determined throughout the box girder. The forces that are determined include bending moment and shear,
Conrad P. Heins, James C. Oleinik
openaire +1 more source
Journal of the Aeronautical Sciences, 1937
] \ / f ANY studies have been made of the elastic be^-*havior of the structure of airplane wings and a number of theories have been advanced as a result of these studies. In general, however, it may be said that too little attention has been directed in these studies to the properties of the shear webs and their relative importance in defining the ...
openaire +1 more source
] \ / f ANY studies have been made of the elastic be^-*havior of the structure of airplane wings and a number of theories have been advanced as a result of these studies. In general, however, it may be said that too little attention has been directed in these studies to the properties of the shear webs and their relative importance in defining the ...
openaire +1 more source
LONGITUDINAL CRACK IN PRESTRESSED BOX BEAM
PCI Journal, 1969A WIDE AND DEEP LONGITUDINAL CRACK DEVELOPED IN THE BOTTOM OF A BRIDGE BOX BEAM AND EXTENDED FROM ONE SUPPORT ALMOST TO MID-SPAN. A DETERMINATION OF THE MOST PROBABLE CAUSE OF THE CRACK AND AN EVALUATION OF THE ULTIMATE AND RESERVE STRENGTH OF THE BEAM BY LOAD TESTING TO FAILURE WERE MADE.
Edward G. Nawy, Herbert Goodkind
openaire +1 more source
Damped Vibrations of Inhomogeneous Composite Box Beams
Vestnik St. Petersburg University, MathematicszbMATH Open Web Interface contents unavailable due to conflicting licenses.
V. M. Ryabov +2 more
openaire +2 more sources
Shear deformable finite beam elements for composite box beams
Acta Mechanica Sinica, 2014zbMATH Open Web Interface contents unavailable due to conflicting licenses.
Kim, Nam-Il, Choi, Dong-Ho
openaire +2 more sources

