Results 121 to 130 of about 88,573 (165)
Some of the next articles are maybe not open access.
Diaphragms for Curved Box Beam Bridges
Journal of the Structural Division, 1975A finite difference procedure is used to determine the response of a single span curved single box beam bridge with any number of interior diaphragms. The bending and torsional distortions as well as cross-sectional distortions can then be determined throughout the curved box girder. The forces that are determined include bending moment and shear, pure
James C. Oleinik, Conrad P. Heins
openaire +1 more source
Aeroelastic tailoring of composite box beams
35th Aerospace Sciences Meeting and Exhibit, 1997Aeroelastic instabilities are an important factor in the design of modern high-speed, flexible aircraft. The current trend is toward the creative use of composites to delay these instabilities. To obtain an optimum design, an accurate as well as efficient model is required.
Mayuresh Patil, Mayuresh Patil
openaire +1 more source
Behavior of Long Fatigue Cracks in Cellular Box Beam
Journal of Structural Engineering, 1999The propagation of long cracks under constant amplitude cyclic loading is studied in complex welded box beams made of high strength low alloy (HSLA) steel. The 8 x 1 x 0.7 m box beams were designed to simulate the cellular structure of a double hull ship but the results of the experiments are equally applicable to other box systems such as bridges ...
Nussbaumer, Alain +2 more
openaire +1 more source
Formulation and Evaluation of an Analytical Model for Composite Box‐Beams
Journal of the American Helicopter Society, 1990A direct method for determining the effective elastic stiffnesses and deformation behavior of composite box-beam (BB) structures is developed analytically, validated, and demonstrated. The BB walls are modeled as orthotropic-ply laminated plates, so that the elastic properties vary both through the thickness and around the BB contour; deformation is ...
EDWARD SMITH, INDERJIT CHOPRA
openaire +1 more source
2015
The previous chapter clearly showed that shear-based piezoceramic actuation using \(d_{15}\) is feasible for obtaining active twist. The current chapter dwells more on the development and validation of the concept of induced-shear-based piezoceramic actuation in helicopter rotor blades considering a simple two-cell box cross section.
Ranjan Ganguli +2 more
openaire +1 more source
The previous chapter clearly showed that shear-based piezoceramic actuation using \(d_{15}\) is feasible for obtaining active twist. The current chapter dwells more on the development and validation of the concept of induced-shear-based piezoceramic actuation in helicopter rotor blades considering a simple two-cell box cross section.
Ranjan Ganguli +2 more
openaire +1 more source
Some Theoretical Considerations on Box Beams
The Journal of the Royal Aeronautical Society, 1941SummaryBox beams, built up essentially with flanges and webs are widely used in aircraft construction and much has been written about their calculation. But often assumptions are implicitly made without reason. The first aim of this paper is to point out which assumptions must be chosen and why, and to show what results may be expected from them.
openaire +1 more source
Box beam shear stresses and deflections
1989The simple beam with loading in one plane was considered in Chapter 4. This type of beam has many applications, such as floor beams for buildings and bridges. However, there are many applications such as airplane wings and fuselages where the beam must take bending in two directions as well as torsional moments. This type of beam which can take all six
openaire +1 more source
Tests on reinforced plywood box beams
Building Research and Practice, 1973Traditional plywood box beams depend to a considerable extent on the strength of natural timber for their flanges, and for reasons of safety only the highest grade of timber should normally be used, particularly when it is not laminated or when there is an abrupt change of direction at midspan.
openaire +1 more source
Torsion-Bending Stresses in Box Beams
Journal of the Aeronautical Sciences, 1948Since the problem of determining bending stresses due to torion in a box beam is closely related to the problem of finding end loments in a continuous beam, it is possible to determine torsionending stresses by a procedure similar to the Cross method of loment distribution widely used in the analysis of continuous :ames.
openaire +1 more source
The Ultimate Strength of Multiweb Box Beams in Pure Bending
Journal of the Aeronautical Sciences, 1955A method for predicting the ultimate bending strength of multiweb box beams having formed sheet metal webs is presented. Equations are derived on the assumption that the ultimate moment is reached when local crippling occurs at the junctions of the webs and the compression skin. The proposed theory is compared with 49 beams fabricated from 75S-T6 sheet
openaire +2 more sources

