Results 21 to 30 of about 22,569 (218)
Physica Scripta, 2021 In the current investigation, a new version of brazing entitled FSVB (friction stir vibration brazing) is developed. In this process, the adjoining samples are vibrated normally to the brazing line while FSB is performed.
V. Rizi, M. Abbasi, B. Bagheri
semanticscholar +1 more source
Overview of nickel-based filler metals for brazing of austenitic stainless steels
Non-ferrous Metals, 2021 The austenitic stainless steels, which are given the most attention in this overview, are widely used in many industries. The exceptional complex of properties of these steels allows them to be used as structural materials for components of nuclear ...
M. Penyaz +3 more
semanticscholar +1 more source
Defence Technology, 2019 The aim of this research study was to determine optimal resistance spot brazing parameters for joining between AHSS and AISI 304 stainless steel by using filler metal.
Niwat Mookam
doaj +1 more source
MATEC Web of Conferences, 2016 The brazing behavior of 3003 fin assemble with 4343(filler layer)/4A60(transition layer)/08Al(steel layer) brazing sheet (the ratio of filler layer thickness to transition thickness were constant 1:2) were investigated.
Sun Chang +3 more
doaj +1 more source
Journal of Materials Research and Technology, 2021 In this paper, the intermetallic compound (IMC) growth behaviors of Sn/Cu and Sn–0.6SiC/Cu solder under isothermal aging (50, 100, 150, 200 and 250 h) and thermal cycling (300, 600, 900, 1200 and 1500 cycles) were studied. The results manifested that the
Mu-lan Li +5 more
doaj +1 more source
Crystals, 2020 The microstructure and mechanical properties of brazing SiC ceramic with Zr-Cu filler metal under different brazing parameters (brazing temperature, holding time) were investigated. The phase of the joint reaction interface between Zr-Cu filler metal and
Bofang Zhou +4 more
doaj +1 more source
Structure formation of seams using high-entropic brazing filler metal MnCoNiCuGe5
Discover Mechanical EngineeringThis study presents the results of metallographic and micro–X-ray spectral investigations of the interfacial boundary between a high-entropy MnCoNiCuGe₅ brazing filler metal and base materials after spreading on nickel (Ni), corrosion-resistant steel ...
Svitlana Maksymova +2 more
doaj +1 more source
Environmental Progress &Sustainable Energy, EarlyView.Abstract Brazed plate heat exchanger (BPHE) was analyzed using computational fluid dynamics (CFD) simulations by ANSYS Fluent to investigate the chevron‐patterned plates. The influence of geometric parameters, including corrugation pitch, depth, and angle was analyzed.
J. S. Huang, K. B. Then, X. W. Wang
wiley +1 more source
Low-Temperature Brazing of Titanium Using Al-Based Filler Alloys
Advances in Materials Science and Engineering, 2018 Brazing of titanium using low melting temperature filler alloys is a preferred choice regarding cost and preserving its mechanical properties. However, brazing titanium at low temperature is still a challenge, especially regarding aluminum-based filler ...
A. Muhrat, H. Puga, J. Barbosa
doaj +1 more source
Heat Transfer, Volume 55, Issue 6, Page 3495-3522, September 2026.ABSTRACT Compact plate‐fin heat exchangers (PFHEs) are commonly utilized in diverse industries, including aerospace, automotive, processing, and space. Various fin configurations, such as Plain fins, Wavy fins, Lance and Offset fins (OSFs), Perforated fins, louvered fins, and pin fins, are employed in compact heat exchangers (CHEs).
Chennu Ranganayakulu
wiley +1 more source