Results 31 to 40 of about 1,825 (173)
Journal of Materials Research and Technology, 2021 In this paper, the intermetallic compound (IMC) growth behaviors of Sn/Cu and Sn–0.6SiC/Cu solder under isothermal aging (50, 100, 150, 200 and 250 h) and thermal cycling (300, 600, 900, 1200 and 1500 cycles) were studied. The results manifested that the
Mu-lan Li +5 more
doaj +1 more source
Crystals, 2020 The microstructure and mechanical properties of brazing SiC ceramic with Zr-Cu filler metal under different brazing parameters (brazing temperature, holding time) were investigated. The phase of the joint reaction interface between Zr-Cu filler metal and
Bofang Zhou +4 more
doaj +1 more source
Influence of the Mg and Bi content on brazeability of MONOBRAZE material under flux-free brazing conditions [PDF]
MATEC Web of Conferences, 2020 In the conventional brazing, the clad materials with the filler layer and the flux coating have been used to get good brazeability. However, an innovative Al-Si based single-layer brazing material (MONOBRAZE® material) has been developed recently which ...
Phumprasop Kanokploy +3 more
doaj +1 more source
Structure formation of seams using high-entropic brazing filler metal MnCoNiCuGe5
Discover Mechanical EngineeringThis study presents the results of metallographic and micro–X-ray spectral investigations of the interfacial boundary between a high-entropy MnCoNiCuGe₅ brazing filler metal and base materials after spreading on nickel (Ni), corrosion-resistant steel ...
Svitlana Maksymova +2 more
doaj +1 more source
Low-Temperature Brazing of Titanium Using Al-Based Filler Alloys
Advances in Materials Science and Engineering, 2018 Brazing of titanium using low melting temperature filler alloys is a preferred choice regarding cost and preserving its mechanical properties. However, brazing titanium at low temperature is still a challenge, especially regarding aluminum-based filler ...
A. Muhrat, H. Puga, J. Barbosa
doaj +1 more source
Metals, 2022 To meet the lightweight demands of automobiles, Al composite sheets require excellent mechanical properties under the condition of minimal thickness after high-temperature brazing processing.
Minglong Kang +7 more
doaj +1 more source
Nondestructive Testing of Welded Composite Metal Foams
Advanced Engineering Materials, EarlyView.X‐ray computed tomography (CT) is used to evaluate welded steel–steel composite metal foam (CMF) joints of two density classes. It reports variation in postweld spatial void distribution and correlates it to weld‐induced changes, mechanical performance, and failure within welded CMF panels.
Chinmaya Prerana Inguva +2 more
wiley +1 more source
Advances in Magnesium‐Based Thermoelectrics: A Critical Review
Advanced Materials, EarlyView.Magnesium‐based thermoelectric materials have emerged as promising candidates for low‐to‐mid‐temperature energy conversion due to their abundance, low cost, and competitive performance. This review summarizes recent advances in Mg3X2, MgAgSb, and Mg2X systems, covering transport mechanisms, fabrication strategies, stability challenges, and device ...
Li‐Min Zhang +5 more
wiley +1 more source
Metals, 2020 Aluminum/Copper dissimilar metal connection devices have been widely used in equipment manufacturing. Ultrasonic vibration assisted semi-solid brazing technology is beneficial to improve brazing quality by using the good flow ability and strong ...
Yin Liang +6 more
doaj +1 more source
High‐Temperature Heat Pump Test Bench with n‐Butane (R‐600) Generating Steam
Chemie Ingenieur Technik, EarlyView.This work involves building a test bench for a high‐temperature heat pump (HTHP) and analyzing the measurements. The focus is on steam generation using an HTHP to decarbonize process steam demand. The findings indicate that stable steam generation is possible, providing a higher heat transfer coefficient in the heat pump's condenser.
Sebastian Benkert +7 more
wiley +1 more source