Results 81 to 90 of about 66,508 (302)
Advanced Engineering Materials, EarlyView.Nickel‐based alloys are widely used in high‐temperature applications due to their excellent mechanical strength and oxidation resistance. However, properties such as high‐temperature strength and pronounced work‐hardening make them difficult to machine.
Soheil Rooein +2 more
wiley +1 more source
Advances in Ductile Iron Research: new metallurgical understanding and its technological significance [PDF]
, 2005 The present work gives an updated view about important metallurgical concepts, concerning the influence that solidification structure, microsegregation, piece size and austenite characteristics, exert on final microstructure, properties and processing ...
Boeri, Roberto Enrique +1 more
core
Cr2C3–NiCr VPS thermal spray coatings as candidate for chromium replacement [PDF]
, 2013 The present investigation has been carried out with the aim of determining the tribological behavior of a VPS chromium carbide coating both in the as-deposited and heat-treated conditions. A commercial powder of Cr2C3–25% NiCr was sprayed employing a VPS
Chicot, Didier +5 more
core +8 more sources
Sol–Gel Derived Polymer Precursors for Stereolithography of ZrC
Advanced Engineering Materials, EarlyView.ZrC is a critical material target for extreme temperature conditions. This report describes a protocol for preparing ZrC ceramics via stereolithography and examines the impact of the polymer matrix on carbothermal reduction and mechanical stability of 3D printed ZrC.
Charles J. Rafalko +2 more
wiley +1 more source
Recent advances in MXene-based materials for high-performance metal-air batteries
Green Chemistry Letters and ReviewsMXene is a novel type of 2D sheet nanomaterial that shows great application potentials in a variety of fields due to its advantages, such as high electrical conductivities, high surface areas, superior mechanical strength, functional transition metal ...
Ababay Ketema Worku +4 more
doaj +1 more source
Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger +2 more
wiley +1 more source
, 2012 Austenite reversion during tempering of a Fe-13.6Cr-0.44C (wt.%) martensite results in an ultrahigh strength ferritic stainless steel with excellent ductility.
Choi, P. +5 more
core +1 more source
Methane cracking over cobalt molybdenum carbides [PDF]
, 2018 The catalytic behaviour of Co3Mo3C, Co6Mo6C, Co3Mo3N and Co6Mo6N for methane cracking has been studied to determine the relationship between the methane cracking activity and the chemical composition.
Alshibane, I. +3 more
core +1 more source
Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V
Advanced Engineering Materials, EarlyView.Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena +2 more
wiley +1 more source
First-principles study, fabrication and characterization of (Zr0.25Nb0.25Ti0.25V0.25)C high-entropy ceramic [PDF]
, 2019 The formation possibility of a new (Zr0.25Nb0.25Ti0.25V0.25)C high-entropy ceramic (ZHC-1) was first analyzed by the first-principles calculations and thermodynamical analysis and then it was successfully fabricated by hot pressing sintering technique ...
Chu, Yanhui +5 more
core +2 more sources