Results 31 to 40 of about 80,916 (315)
Materials Research Express, 2020 AE44-2 magnesium (Mg) alloys were fabricated by gravity casting (GC), high pressure die casting (HPDC), and high vacuum assisted high pressure die casting (HVHPDC).
Taihe Le +5 more
doaj +1 more source
Metals, 2020 In this work, a plant trial was conducted on an industrial low pressure die casting (LPDC) manufacturing process for the production of aluminum alloy wheels.
Jun Ou +7 more
doaj +1 more source
Quench Sensitivity and Phase Transformation Kinetics of AlSi7MnMg High Pressure Vacuum Die Casting [PDF]
MATEC Web of Conferences, 2020 The quench sensitivity of an AlSi7MnMg alloy in high-pressure vacuum die (HPVD) casting was investigated by time-temperature-transformation and time-temperature-property diagrams with an interrupted quench technique.
Liu Mengyun +3 more
doaj +1 more source
Relationship between casting modulus and grain size in cast A356 aluminium alloys [PDF]
, 2012 Microstructure of Al-Si alloy castings depends most generally on melt preparation and on the cooling rate imposed by the thermal modulus of the component. In the case of Al-Si alloys, emphasis is put during melt preparation on refinement of pro-eutectic (
+22 more
core +4 more sources
Die Casting Die Design and Process Optimization of Aluminum Alloy Gearbox Shell
Materials, 2021 Taking an aluminum alloy gearbox of an automobile as an example, according to its structural characteristics, the parting surface was determined, and the initial gating system was designed by using 3D modeling software UG.
M. Huang +3 more
semanticscholar +1 more source
Microstructural characteristics of diecast AlMgSiMn alloy [PDF]
, 2014 Solidification and microstructural characteristics of Al-5wt.%Mg-1.5wt.%Si-0.6wt.%Mn- 0.2wt.%Ti alloy have been investigated in high pressure die casting. The average size of dendrites and fragmented dendrites of the primary α-Al phase formed in the shot
Fan, ZY, Ji, SX, Wang, Y, Watson, D
core +1 more source
A control and monitoring oriented model of a film manufacturing process [PDF]
, 2008 This paper describes the development of a control and monitoring oriented model of a plastic film manufacturing process. The model is mainly derived from first-principles and has been implemented in the Matlab/Simulink dynamic simulation environment. The
Balderud, Jonas +3 more
core +1 more source
Faster - Better Molds Through RSP Tooling New Research and Advancements [PDF]
, 2004 The recent developments in rapid production tooling have all but made the need for prototype tooling disappear. There are several approaches that are now as fast and inexpensive as prototype tooling, and after part approval can continue to run in high ...
Knirsch, James R.
core +1 more source
Effect of iron on the microstructure and mechanical property of Al-Mg-Si-Mn and Al-Mg-Si diecast alloys [PDF]
, 2013 This article is made available through the Brunel Open Access Publishing Fund. Copyright @ 2012 Elsevier B.V.This article has been made available through the Brunel Open Access Publishing Fund.Al–Mg–Si based alloys can provide super ductility to satisfy ...
Ji, S +4 more
core +1 more source
Modeling studies on divorced eutectic formation of high pressure die cast magnesium alloy [PDF]
China Foundry, 2018 The morphology and content of the divorced eutectic in the microstructure of high pressure die casting (HPDC) magnesium alloy have a great influence on the final performance of castings.
Meng-wu Wu, *Lin Hua, Shou-mei Xiong
doaj +1 more source