Results 41 to 50 of about 1,785 (154)
Effect of Water Mist Cooling on Microstructure of Hypereutectic Al-Si Alloy
Archives of Foundry Engineering, 2014 The work is a continuation of research on the use water mist cooling in order to increase efficiency of die-casting aluminum alloys using multipoint water mist cooling system.
Władysiak R., Kozuń A.
doaj +1 more source
Archives of Metallurgy and Materials, 2017 Unmodified AlSi20 alloy were casted at the research station, allowing for sequential multipoint cooling using a dedicated computer- controlled program.
Władysiak R., Kozuń A., Pacyniak T.
doaj +1 more source
An overview of high thermal conductive hot press forming die material development [PDF]
Journal of Mechanical Engineering and Sciences, 2015 Most of the automotive industries are using high strength steel components, which are produced via hot press forming process. This process requires die material with high thermal conductivity that increases cooling rate during simultaneous quenching and ...
A.R. Zulhishamuddin, S.N. Aqida
doaj +1 more source
Control and optimization of defects in die casting of complicated right crankcase cover
Journal of Materials Research and TechnologyThe die-casting process of ADC12 aluminum alloy right crankcase cover was simulated based on AnyCasting software, and the influence of pouring temperature, initial mold temperature and injection speed on the filling and solidification process of ADC12 ...
Hong Xu +7 more
doaj +1 more source
Structure of Water Mist Stream and its Impact on Cooling Efficiency of Casting Die
Archives of Foundry Engineering, 2012 Structure of Water Mist Stream and its Impact on Cooling Efficiency of Casting Die The work is a continuation of research on the use water mist cooling in order to increase efficiency of die-casting aluminum alloys. The paper presents results of research and analysis process, spraying water and generated a stream of water mist, the effect of ...
R. Władysiak, P. Budzyński
openaire +1 more source
Fluid Flow and Heat Transfer Simulations of the Cooling System in Low Pressure Die Casting
Celal Bayar Üniversitesi Fen Bilimleri Dergisi, 2020 Low pressure die casting (LPDC) is the preferred method to manufacture cost-effective automotive wheels. Cooling systems and channels of a low pressure die casting are critical to obtain better mechanical properties. Both steady-state and time-dependent (transient) Computational Fluid Dynamics (CFD) analyses of the cooling channels and the die ...
OZAYDİN, Onur +3 more
openaire +2 more sources
Computer simulation for prediction of thermal distortion of JIS ADC12 flat-shape die-casting
Nihon Kikai Gakkai ronbunshu, 2014 A computer simulation method to predict the thermal distortion value of a high-pressure die cast part was investigated. The evaluated product was a flat-shape JIS ADC12 part. The actual distortion value of the part was measured by an optical 3D digitizer
Hiroshi YAMAGATA +3 more
doaj +1 more source
Residual stresses in castings produced by press die casting technology
Metalurgija, 2015 The influence of technological parameters on residual stresses in pressure die castings is analysed in this paper. In order for the residual stresses to be as low as possible the optimization of technological parameters is necessary.
D. Novoselović +2 more
doaj
Analysis of Crystallization Process of Intensive Cooled AlSi20CuNiCoMg Alloy
Archives of Foundry Engineering, 2017 The work is a continuation of research concerning the influence of intensive cooling of permanent mold in order to increase the casting efficiency of aluminium alloys using the multipoint water mist cooling system.
Władysiak R. +3 more
doaj +1 more source
Materials Research ExpressResearch into semi-solid metal forming techniques has been ongoing for an extended period with the aim of producing near-net shape products from aluminum alloys.
Serhat Acar, Kerem Altug Guler
doaj +1 more source