Results 111 to 120 of about 17,824 (316)

A Study Of Caste Dynamics In Bihar: Casting And Casting Out

, 2015
Indian Caste System and Its Dynamics.
openaire   +1 more source

Enhanced Strength and Corrosion Resistance of Ti‐13Nb‐12Ta‐10Zr‐4Sn Alloy by Aging Treatment

Advanced Engineering Materials, EarlyView.
This work systematically investigates the effect of aging treatment on mechanical properties and corrosion behavior of vacuum arc‐melted Ti‐13Nb‐12Ta‐10Zr‐4Sn alloy. Owing to the increased α″ martensite, strength and corrosion resistance were significantly enhanced by aging treatment.
Yuhua Li, Rong Zhao, Qian Zhang, Haojie Wang, Yujing Liu, Lai‐Chang Zhang   +5 more
wiley   +1 more source

The BTEX emission from moulding sands with furan resin dependence on the VOC content and loss on ignition

Metalurgija, 2015
The article contains the results of emission BTEX (benzene, toluene, ethylobenzene and xylenes) during thermal destruction (500 – 1 300 °C) of moulding sand with furan resin.
S. Żymankowska-Kumon
doaj  

Direct Metal Deposition of Graphene–Ti28Nb35.4Zr Matrix Composites With Enhanced Mechanical, Corrosion, and Biocompatibility Properties for Bone Implants

Advanced Engineering Materials, EarlyView.
Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir, Jixing Lin, Yuncang Li, Li Zhu, Paul F. A. Wright, Cuie Wen   +5 more
wiley   +1 more source

Cathodic Cage Plasma Deposition of Nanostructured Cu–Fe–Se Coatings on Poly(methyl Methacrylate)

Advanced Engineering Materials, EarlyView.
Nanostructured Cu–Fe–Se coatings are deposited on PMMA by a modified cathodic cage plasma process, enabling low‐temperature deposition on polymer substrates. A transition from discontinuous to compact morphology is observed with temperature, with optimal properties at 200°C, where improved CuFeSe2‐type bonding, lowest sheet resistance, and favorable ...
V. S. S. Sobrinho, M. Naeem, T. H. C. Costa, M. S. Libório, J. C. A. Queiroz, C. B. B. Luna, R. R. M. Sousa, P. S. Vieira, E. M. Araújo   +8 more
wiley   +1 more source

An Experimental High‐Throughput Approach for the Screening of Hard Magnet Materials

Advanced Engineering Materials, EarlyView.
An entire workflow for the high‐throughput characterization and analysis of compositionally graded magnetic films is presented. Characterization protocols, data management tools and data analysis approaches are illustrated with test case Sm(Fe, V)12 based films.
William Rigaut, Pierre Le Berre, Hamdi Jaballah, Lukas Fink, Victor Poline, Richard Haettel, Stéphane Grenier, Gilbert Chahine, Ewen Bellec, Guillaume Buatier, Wilfried Hortschitz, Santa Pile, Thomas Schrefl, Nils Blanc, Yuan Hong, Thibaut Devillers, Nora M. Dempsey   +16 more
wiley   +1 more source

Nondestructive Testing of Welded Composite Metal Foams

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography (CT) is used to evaluate welded steel–steel composite metal foam (CMF) joints of two density classes. It reports variation in postweld spatial void distribution and correlates it to weld‐induced changes, mechanical performance, and failure within welded CMF panels.
Chinmaya Prerana Inguva, Aman Kaushik, Afsaneh Rabiei   +2 more
wiley   +1 more source

Experimental Characterization and Constitutive Modeling of the Effect of Prior Inelastic Strain on the Viscoplastic Behavior of AD730 at 700 °C

Advanced Engineering Materials, EarlyView.
This study shows that superalloys used in aircraft engine disks become much more prone to deformation at high temperatures if they have been strained during manufacturing. This effect increases with the level of prior strain but eventually reaches a limit.
Fabio Machado Alves da Fonseca, Patrick Villechaise, Malik Durand, Arnaud Longuet, Florent Coudon, Loïc Signor, Julien De Jaeger, Dominique Eyidi, Nathalie Bozzolo, Jonathan Cormier   +9 more
wiley   +1 more source

USE OF TECHNOLOGY OF PRECISION CASTING INTO DISPOSABLE CERAMIC MOLD FOR PRODUCTION OF SHAPED CASTINGS AND OF CASTINGS WITH THE HIGHER PERFORMANCE REQUIREMENTS

Литьë и металлургия, 2017
Through the example of production of specific castings the effectiveness of the precision ceramic molding technology for the production of shaped castings and castings with the higher performance requirements has been demonstrated.
B. I. Uvarov, P. E. Lushchyk, A. A. Andrits, L. P. Dolgiy, A. V. Zablotskiy   +4 more
doaj  

Device for Making Castings.

, 1909
Patent for "making castings of various kinds, and more especially for making castings for dental use" (lines 10-12) including ...
Davison, Hugh M.
core