Results 81 to 90 of about 109,713 (306)

Cryogenic Deformation Behavior of TiAl and Insights Into Embrittlement After High‐Temperature Exposure Combined With Secondary Ion Mass Spectroscopy of Near Surface Chemistry

Advanced Engineering Materials, EarlyView.
Near‐surface deuterium enrichment profiles for different microstructural types of TiAl after exposure at 700 °C in a heavy water‐containing environment. The deuterium levels are significantly higher than expected from natural occurrence, indicating that the heavy water dissociated during the exposure treatment and entered the specimens.
Jonathan D. H. Paul, Alexander Welle, Dirk Matthiessen, Michael Oehring, Fritz Appel, Florian Pyczak   +5 more
wiley   +1 more source

Raw data of CTD casts of RV Maria S. Merian cruise MSM25

, 2021
The dataset consists of single-dip casts and tow-yo casts. During most of the tow-yo casts a Posidonia USBL transponder was mounted to the CTD.
Walter, Maren, Schmid, Florian
core   +1 more source

Enhancement of the Through‐Thickness Electrical Conductivity of Carbon‐Fiber‐Reinforced Plastics Using Large Graphite Particles

Advanced Engineering Materials, EarlyView.
To enhance through‐thickness conductivity without sacrificing impregnation, large spherical graphite particles are intentionally employed in a low‐viscosity resin. Unlike finer conductive fillers, these particles remain outside the fiber bundles and accumulate in resin‐rich interlaminar regions during molding.
Keito Hosoe, Yu Zhou, Shintaro Kamiyama, Takao Okada, Tomohiro Yokozeki, Ryoma Tokonami, Tatsuhiro Takahashi   +6 more
wiley   +1 more source

3D‐Printed Titanium Gyroid Scaffold Structure Integrated With Tough Hybrid Materials for Cartilage Replacement

Advanced Engineering Materials, EarlyView.
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin, Gloria R. Young, Francesca Tallia, Reece N. Oosterbeek, Shaaz Ghouse, Edward Spiers, Nupur Kohli, Tom Briggs, Marc Masen, Siwei Li, Ren‐Jei Chung, Jonathan R. T. Jeffers, Julian R. Jones   +12 more
wiley   +1 more source

Comparison of dental arch measurements between 3D-printed, digital, and stone casts

Future Science OA
Background The use of computer-aided design and manufacturing technologies in diagnosis, treatment planning, and fabrication of prosthetic restoration is changing how prosthodontic treatment is offered to patients.
Noor Al Mortadi, Karem H. Alzoubi, Mohammad Alzoubi   +2 more
doaj   +1 more source

Embodied energies, embedded stories: releasing the potential of casts of early medieval sculptures

, 2013
This paper explores the story-telling (cultural biographical) potential of plaster casts, specifically the casts made since the early nineteenth-century of early medieval sculpture in Britain and Ireland.
Foster, Sally
core  

Elastic–Plastic Modeling and Experimental Characterization of Granular Jamming Actuators

Advanced Engineering Materials, EarlyView.
Granular jamming enables rapid switching between soft and rigid mechanical states. Here, a reduced‐order elastic‐perfectly‐plastic beam framework captures pressure‐dependent loading, unloading, residual deformation, and hysteresis in jammed beams, while matching three‐point bending experiments across materials and geometries. The framework links design
Saheli Patel, Prashant K. Purohit, Jordan R. Raney   +2 more
wiley   +1 more source

ADDENDUM: Casts for Verdi Premieres in the United States; Casts for Verdi Premieres in London [PDF]

, 1983
Addenda to Martin Chusid\u27s Casts for the Verdi Premieres in the United States (Verdi Newsletters 2 & 3) and Casts for the Verdi Premieres in London (Verdi Newsletters 5 & 6)
Chusid, Martin
core   +1 more source

Mitigating Creep Anisotropy and Enhancing Performance in Additively Manufactured Ni‐Based Superalloys: A Review

Advanced Engineering Materials, EarlyView.
Additive manufacturing introduces pronounced microstructural and crystallographic anisotropy in Ni‐based superalloys, resulting in orientation‐dependent creep deformation and damage. This review identifies the key microstructural origins of creep anisotropy, examines their influence on dominant deformation mechanisms, and highlights processing ...
Chandan Kumar, Shobhit Pratap Singh, Gaurav Mohanty, Praveen Kumar   +3 more
wiley   +1 more source

Evaluation of patient preference in 3D printed cast and associated cost compared to current standard of care

Annals of 3D Printed Medicine
Background: Fracture incidence is rising globally, with traditional fiberglass casts commonly used for immobilization despite discomfort and hygiene issues. 3D printed casts offer similar or improved strength, better comfort, and breathability.
Rand Kittani, Alexis Watson, Sydni Silverman, Kaviamuthan Kanakaraju, Jaime Chen, Jose Beltran, Thomas Murphy   +6 more
doaj   +1 more source