Results 201 to 210 of about 11,271 (232)

Erosion, Cavitation, and Abrasion Resistance of Choke Trim Materials

Offshore Technology Conference, 1984
ABSTRACT An experimental investigation was performed to determine the relative erosion, abrasion and cavitation resistance characteristics of selected materials. Testing was conducted under controlled laboratory conditions to simulate service conditions encountered in production and injection chokes.
F.G. Seger, I. Maroofian
openaire   +1 more source

Cavitation erosion resistance parameter of hard CAVD coatings

Progress in Organic Coatings, 2011
Abstract Nowadays the most machining tools are coated with hard coatings to prolong their lifetime and to improve their working efficiency. They are very often used for high wear applications, where they are subjected to cyclic impact loading. Main benefits of hard coatings are based on the combination of high hardness and toughness, properties that ...
openaire   +1 more source

Investigating Polymeric Elastomers for Cavitation and Erosion Resistance

Materials Performance
Cavitation and erosion damage are observed on water infrastructure. Mitigating degradation on mild steel traditionally includes stainless-steel weld overlays, which create a galvanic corrosion cell in immersion conditions. This can cause delamination of the stainless steel and subsequent loss of cavitation or erosion protection.
Allen Skaja, Christine Henderson
openaire   +1 more source

Cavitation erosion resistance of metglas alloy 2826 MB

Journal of Materials Science Letters, 1984
Etude de la resistance a l'erosion par cavitation d'un ruban de verre metallique Fe 40 Ni 38 Mo 4 B 18 , comparee a celle de l'acier doux typique En1A. Les essais de cavitation sont effectues dans une emulsion huile (5%) dans l'eau a 50 C, l'echantillon etant soumis a une vibration de 20 kHz avec une amplitude de 50 μm.
openaire   +1 more source

Deformation-Induced Martensite and Resistance to Cavitation Erosion

Journal de Physique IV, 1995
Exposure to cavitating liquids can induce surface transformation in metastable alloys, notably the 18Cr-8Ni class of stainless steels. The question of whether such transformation contributes to erosion resistance has not been resolved. To address that issue, two metastable stainless steels (Types 301 and 304L) and a near-equiatomic NiTi alloy were ...
openaire   +1 more source

Cavitation-Erosion Resistance of Thick-Film Thermally Sprayed Niti

MRS Proceedings, 1990
AbstractThermal spray technologies provide a method for depositing high temperature intermetallics. Deposits of Shape Memory Effect NiTi were produced by Electric-Arc Spraying (EAS) of NiTi wire, Vacuum Plasma Spraying (VPS) of NiTi powder, and codeposition of Ni and Ti using VPS. NiTi deposits displayed shape memory effect properties, which are highly
A. Peter Jardine, Y. Horan, H. Herman
openaire   +1 more source

International Cavitation Erosion Test and quantitative assessment of material resistance to cavitation

Wear, 1999
Abstract In September 1987, during the ELSI VII Conference, the start of the International Cavitation Erosion Test (ICET) project was announced. The experimental programme consisted in testing 6 selected materials (single-phase aluminium and brass alloys, Armco iron, carbon and chromium–nickel steel, and a polyamide 6 plastics) at various laboratory ...
openaire   +1 more source

Cavitation Erosion Resistance of Materials

Journal of the Society of Mechanical Engineers, 1988
Tsunenori OKADA, Yoshiro IWAI
openaire   +1 more source

Resistance of cast irons to cavitational erosion

Metal Science and Heat Treatment, 1966
I. N. Bogachev, V. F. Senkevich, T. M. Petukhova   +2 more
openaire   +1 more source

Antibiotic resistance in the patient with cancer: Escalating challenges and paths forward

Ca-A Cancer Journal for Clinicians, 2021
Amila K Nanayakkara, Kevin Outterson
exaly