Results 171 to 180 of about 64,179 (268)

Clay Ceramic Pellets for Water Treatment

Two different Quaternary clays from deposits Slucenieki and Prometejs were used for production of porous ceramic pellets. 3 wt % of sawdust additive was used to increase porosity of the obtained ceramic.
Švinka, Ruta, Švinka, Visvaldis, Damberga, Mārīte, Pudže, Inga   +3 more
core  

The ceramic history of West Pans Part 2

, 2006
The West Pans ceramic material, listed described and photographed on the enclosed disk has been assigned to the National Museums of Scotland and was catalogued using accession numbers (MES1.1 to 1132).
Forbes, Sheila, Haggarty, George
core  

Sol-Gel-Free Electrospinning of α‑Al₂O₃ Suspensions: A Systematic Study on Processing Commercial Powders into Ceramic Fibers. [PDF]

ACS Omega
Fuentes-García JA, Gurauskis J.
europepmc   +1 more source

Workflow for Design of Experiments‐Based Modeling of Species Transport and Growth Kinetics in GaN Hydride Vapor Phase Epitaxy

Advanced Engineering Materials, EarlyView.
A novel workflow for investigating hydride vapor phase epitaxy for GaN bulk crystal growth is proposed. It combines Design of experiments (DoE) with physical simulations of mass transport and crystal growth kinetics, serving as an intermediate step between DoE and experiments.
J. Tomkovič, G. Lukin, H. Torkashvand, A. Kerschbaum, M. Müller, S. Besendörfer, J. Heitmann, J. Friedrich   +7 more
wiley   +1 more source

The Influence of SiC and Al₂O₃ Particles on the Microstructure and Tribological Properties of the EN-GJL-150 Cast Iron-Based Composite. [PDF]

Materials (Basel)
Piatkowski J, Wojciechowski M, Matula T, Nowinska K.   +3 more
europepmc   +1 more source

Soft Mechanical‐Electrical Logic Using Liquid Metal‐Filled 3D‐Printed Architectures

Advanced Engineering Materials, EarlyView.
We present 3D‐printed soft mechanical–electrical logic elements that use liquid metal–filled silicone tubes actuated by thermoplastic polyurethane/polylactic acid (TPU/PLA) architectures to produce Boolean operations. Complementary normally open and normally closed unit cells perform repeatable binary transitions and can be combined into more complex ...
Christoph Lehmann, Ryan Kalgreen, Laura M. Comella   +2 more
wiley   +1 more source

Clay deposits in the Benue Valley, Northern Cameroon: mineralogical, chemical and technological characterisation for uses in ceramic bricks production. [PDF]

Sci Rep
Kagonbé BP, Ngarena KM, Cengiz Ö, Djenabou SF, Bakaïné VD, Yanné E, Djoda FP.   +6 more
europepmc   +1 more source

Enhanced Strength and Corrosion Resistance of Ti‐13Nb‐12Ta‐10Zr‐4Sn Alloy by Aging Treatment

Advanced Engineering Materials, EarlyView.
This work systematically investigates the effect of aging treatment on mechanical properties and corrosion behavior of vacuum arc‐melted Ti‐13Nb‐12Ta‐10Zr‐4Sn alloy. Owing to the increased α″ martensite, strength and corrosion resistance were significantly enhanced by aging treatment.
Yuhua Li, Rong Zhao, Qian Zhang, Haojie Wang, Yujing Liu, Lai‐Chang Zhang   +5 more
wiley   +1 more source

Early experiments in the making of Moravian ceramics in North Carolina c. 1770-1820. [PDF]

NPJ Herit Sci
Sarnecka Z, Bonizzoni L, Brown JM, Sarnecki J, Mazzocchi C.   +4 more
europepmc   +1 more source

Evaluation of Plasticity and Creep Parameters From Tensile Stress–Strain Data for a Range of Strain Rates

Advanced Engineering Materials, EarlyView.
This plot compares experimental tensile stress–strain curves (with 4 different strain rates) and corresponding modelled curves (obtained using the optimised sets of Voce and Miller–Norton parameter values shown). The inferred M‐N values, characterizing the creep, are very similar to those obtained via conventional creep testing.
S. Ooi, R. P. Thompson, T. W. Clyne
wiley   +1 more source