Results 1 to 10 of about 1,091 (180)

Preparation and characterization of coal gangue/Al cermet materials [PDF]

E3S Web of Conferences, 2021
In this study, the calcined coal gangue was mixed with Al powder at different mass fractions (5wt%〜35wt%). After being pressed at 80MPa and sintered at 1200°C for 2h, the coal gangue/Al cermet material was obtained.
Wu Guihua, Tang Lihua
doaj   +1 more source

Structure and ablation behavior of “Z-pins like” M-MC1-x (M = Zr, Hf) gradient cermet rods prepared by carbon diffusion in situ reaction method

Journal of Materials Research and Technology, 2022
In this study, “Z-pins like” M-MC1-x (M = Zr, Hf) gradient cermet rods were prepared by the carbon diffusion in situ reaction method, and the effects of different heat treatment temperatures on the microstructure of MC layers in “Z-pins like” M-MC1-x ...
Xin Qing, Wei Sun, Tian Tian, Hongbo Zhang, Xiang Xiong   +4 more
doaj   +1 more source

A Fuzzy Evaluation of Tool Materials in the Turning of Marine Steels

Metals, 2021
To recommend one suitable tool material for the cutting of marine steels under special conditions and requirements in emergency rescues of capsized steel ships, the cermet tools, cemented carbide tools and coated carbide tools were evaluated using a ...
Qingzhong Xu, Jichen Liu, Gangjun Cai, Dewen Jiang, Jian Zhou   +4 more
doaj   +1 more source

The effect of roller pressure and feed rate on hides squeezing [PDF]

E3S Web of Conferences, 2023
The article presents the results of experimental studies of the process of extracting excess liquid from a water-saturated hide. The experiments were conducted in two options: using a rigid base plate and a cermet base plate for the feed mechanism of the
Bahadirov Gayrat, Tsoy Gerasim, Nabiev Ayder   +2 more
doaj   +1 more source

Comparative Analysis on Reinforcement of Potential Additives in WOKA Cermet HVOF Coating Subjected to Slurry Erosion in Ash Conditions [PDF]

Iranian Journal of Materials Science and Engineering, 2022
In this paper, an investigation was carried out to test the suitability of potential additive materials in WOKA 3533 (WC-10Co4Cr) cermet HVOF coating subjected to slurry erosion in ash conditions.
Jashanpreet Singh, Rana Gill, Satish Kumar, S.K. Mohapatra   +3 more
doaj  

Effects of nanoparticle structural features on the light-matter interactions in nanocermet layers and cermet-based solar absorbers

Journal of Materiomics, 2021
Metallic nanoparticle (NP)/ceramic composite cermets present desirable broadband absorption of the solar spectrum and thus are the preferred material scheme for constructing cermet-based solar absorbers.
Xiaoyu Wang, Houjin He, Junhua Gao, Haibo Hu, Shiwei Tang, Xiaoyun Li, Xiuhong Li, Hongtao Cao   +7 more
doaj   +1 more source

Effect of Synthesis Method of Nickel–Samarium-Doped Ceria Anode on Distribution of Triple-Phase Boundary and Electrochemical Performance

Crystals, 2021
Two-dimensional (2D) electron back scattered diffraction (EBSD) is a powerful tool for microstructural characterization of crystalline materials. EBSD enables visualization and quantification of the effect of synthesis methods on the microstructure of ...
Muhammed Ali Shaikh Abdul, Ahmad Zubair Yahaya, Mustafa Anwar, Mun Teng Soo, Andanastuti Muchtar, Vadim M. Kovrugin   +5 more
doaj   +1 more source

Effects of different HVOF thermal sprayed cermet coatings on tensile and fatigue properties of AISI 1045 steel

Journal of Materials Research and Technology, 2021
The objective of the present work was to investigate the effect of different cermet coatings on tensile and high-cycle fatigue properties of AISI 1045 steel using High-Velocity Oxygen Fuel (HVOF) thermal spray process. In this study, the WC-12Co, WC-10Co-
Gi-Su Ham, R. Kreethi, Hyung-jun Kim, Sang-hoon Yoon, Kee-Ahn Lee   +4 more
doaj   +1 more source

Dataset and methodology on identification and correlation of secondary carbides with microstructure, wear mechanism, and tool performance for different CERMET grades during high-speed dry finish turning of AISI 304 stainless steel

Data in Brief, 2020
The aim of this research is to utilize reverse engineering approach for the identification of the elements and phases available in the commercial CERMET inserts with the help of characterization techniques such as Scanning Electron Microscope (SEM ...
Uttkarsh Patel, Sushant Rawal, A.F.M. Arif, Stephen Veldhuis   +3 more
doaj   +1 more source

Distinguishing contributions of ceramic matrix and binder metal to the plasticity of nanocrystalline cermets

IUCrJ, 2020
Using the typical WC–Co cemented carbide as an example, the interactions of dislocations within the ceramic matrix and the binder metal, as well as the possible cooperation and competition between the matrix and binder during deformation of the ...
Xinru Ge, Xuemei Liu, Chao Hou, Hao Lu, Fawei Tang, Xiangfei Meng, Wenwu Xu, Xiaoyan Song   +7 more
doaj   +1 more source