Results 51 to 60 of about 14,821 (161)
Advanced Engineering Materials, EarlyView.EDX elemental map of the pre‐oxidized MgO–steel cermet anode cross section after electrolysis. The development of inert anodes for aluminum electrolysis remains challenging due to the high corrosivity of cryolite‐based melts at 950°C–1000°C. This study investigates the corrosion and process behavior of a carbon‐free MgO–steel cermet anode derived from ...
Alexander Adamczyk +7 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Micro‐Raman spectroscopy is applied to characterize corrosion products in a recycled‐based MgO–316L steel composite anode after molten salt electrolysis. A depth‐dependent Fe–O/Fe–Al–O layer sequence of magnetite, hercynite, and an Al‐doped magnetite transition zone is identified.
Felix Drechsler +9 more
wiley +1 more source
Metals, 2023 A mathematical model was developed to determine the order of failure of layers in a two-layer ceramics composite and to determine the conditions for achieving the maximum limit load under three-point loading.
Kirill Khvostunkov +5 more
doaj +1 more source
Intermediate temperature SOFC single cell test using Nd1.95NiO4+δ as cathode [PDF]
, 2007 This work deals with SOFC single cell tests using neodymium nickelate Nd1.95NiO4+δ as cathode material. This MIEC oxide exhibits high values of both surface exchange coefficient (k) and oxygen diffusion coefficient (D*), as well as high electronic ...
Ansart, Florence +7 more
core +5 more sources
Advanced Engineering Materials, EarlyView.Cermets (60 vol.% AISI 316L stainless steel, 40 vol.% recycled MgO), intended for use in aluminum electrolysis, were pre‐oxidized in three furnaces with different heating technologies and subjected to a cryolite corrosion test. The different atmospheres influenced the formation of oxide layers, which in turn affected corrosion resistance and ...
Patricia Kaiser +4 more
wiley +1 more source
Stochastic Computer Simulation of Cermet Coatings Formation
Advances in Materials Science and Engineering, 2015 An approach to the modeling of the process of the formation of thermal coatings lamellar structure, including plasma coatings, at the spraying of cermet powders is proposed. The approach based on the theoretical fundamentals developed which could be used
Oleg P. Solonenko +2 more
doaj +1 more source
Photonic Band Gaps in 3D Network Structures with Short-range Order
, 2011 We present a systematic study of photonic band gaps (PBGs) in three-dimensional (3D) photonic amorphous structures (PAS) with short-range order. From calculations of the density of optical states (DOS) for PAS with different topologies, we find that ...
Carl F. Schreck +8 more
core +1 more source
Numerical Study of Heterogeneous Reactions in an SOFC Anode with Oxygen Addition [PDF]
, 2007 Previous experimental studies have shown that addition of small amounts of oxygen to a hydrocarbon fuel stream can control coking in the anode, while relatively large amounts of oxygen are present in the fuel stream in single-chamber solid oxide fuel ...
Goodwin, David G., Hao, Yong
core +2 more sources
Emerging Materials and Future Strategies for Solid Oxide Electrochemical Cells
Advanced Energy Materials, EarlyView.Solid oxide electrochemical cells operate under strongly coupled electrochemical and thermodynamic conditions, where performance is constrained by interactions among crystal structure, defect chemistry, and interfacial evolution. This review, based on a structure‐defect‐property‐durability framework, reveals the roles of lattice symmetry and defect ...
Qiuchun Lu +4 more
wiley +1 more source
Carbon Energy, EarlyView.Systematic alloying of Ni with Cu, Fe, and Co in Ni/YSZ electrodes modifies active site density up to 43%, decreases activation energies by up to 44%, and reduces carbon deposition fourfold. Cu–Ni alloy is among the most promising alloy catalysts for electrochemical CO2 reduction in SOECs.
Min Jun Oh +9 more
wiley +1 more source