Results 71 to 80 of about 15,459 (263)
Electrical Conductivities of Conductors, Semiconductors, and Their Mixtures at Elevated Temperatures
Advanced Engineering Materials, Volume 28, Issue 8, 22 April 2026.This article presents a comprehensive review of temperature‐dependent electrical conductivity data for multiple material classes at elevated temperatures, highlighting a persistent conductivity gap between metals and semiconductors in the range of 102$\left(10\right)^{2}$– 107$\left(10\right)^{7}$ S/m. Metal–ceramic irregular metamaterials are proposed
Valentina Torres Nieto, Marcia A. Cooper
wiley +1 more source
Solid Particle Erosion and Predictive Modeling of Epoxy Composites Reinforced With Diatom Frustules
Polymer Composites, Volume 47, Issue 8, Page 7094-7108, 20 April 2026.Schematic representation of the solid particle erosion process and predictive modeling workflow for diatom frustule‐reinforced epoxy composites, illustrating the test setup, erosion response curve, and filler‐matrix interaction. ABSTRACT This study examines the solid particle erosion wear behavior of epoxy composites reinforced with 5–20 wt% calcined ...
Elif Gültürk +4 more
wiley +1 more source
DEVELOPMENT AND CHARACTERIZATION OF HIGH-PERFORMANCE TiC AND TiN CERMETS
, 2019 ‘Cermets’ are engineered composites that combine ceramic and metallic phases to generate materials that, typically, exhibit both high hardness and toughness. Because of this combination of constituents, cermets can exhibit a moderately low coefficient of
Gaier, Marciel
core
Journal of Materials Research and TechnologyThe present study investigates the dry sliding wear behavior of the TiC-stainless steel-based cermets processed using the Binder Jet 3D Printing technique (BJ3DP).
H.S. Maurya, F. Akhtar, K.G. Prashanth
doaj +1 more source
The Influence of Sintering Temperature of Reactive Sintered (Ti, Mo)C-Ni Cermets
Medžiagotyra, 2015 Titanium-molybdenum carbide nickel cermets ((Ti, Mo)C-Ni) were produced using high energy milling and reactive sintering process. Compared to conventional TiC-NiMo cermet sintering the parameters for reactive sintered cermets vary since additional ...
Marek Jõeleht
doaj +1 more source
A Novel Metal Foam‐Supported Solid Oxide Fuel Cell With High Specific Power
Advanced Science, Volume 13, Issue 19, 2 April 2026.Solid oxide fuel cells (SOFCs) employing metal foam supports with an ultrahigh porosity of 90% and average pore size of 100 µm are successfully fabricated. The metal foam architecture significantly enhances gas diffusion coefficients, effectively reducing concentration polarization while simultaneously decreasing areal mass.
Jingbo Ma +4 more
wiley +1 more source
Erosion-corrosion behaviour of Zirconia WC-6Co, WC-6Ni and SS316
, 2015 The current study investigates a ceramic, two cermets and a metal under solid-liquid impingement with 3.5% NaCl and 150mg/l hydraulic fracturing sand at two extreme angles of impact, 90° and 20°.
Giourntas, L. +3 more
core
Electrodeposition of cermets [PDF]
, 1970 Modern engineering requirements are frequently near the limits of application of conventional materials. For many purposes, particularly tribological, the most satisfactory solution is frequently the application of a resistant coating to the surface of a common metal.
openaire +1 more source
Advanced Science, Volume 13, Issue 20, 9 April 2026.A heterostructured CeZrOx/NiO‐Ni inverse catalyst is designed for highly efficient photothermal CO2 methanation under low‐intensity light without auxiliary heating. It achieves 464 mmol·gcat−1·h−1 methane space‐time yield under natural concentrated sunlight, maintains stability over light‐dark cycles and extended air storage, and is scalable to 100 g ...
Chuqiao Song +16 more
wiley +1 more source
, 2009 This bachelor thesis deals with cermets, as tool material. In the first part of this work is given a basic overview of tool materials. The second part is focused on species, production and properties of cermets. The third part is given comparison cermets
Hanousek, Petr
core