Results 61 to 70 of about 510,694 (243)
MOFs and COFs in Electronics: Bridging the Gap between Intrinsic Properties and Measured Performance
Advanced Functional Materials, EarlyView.Metal‐organic frameworks (MOFs) and covalent organic frameworks (COFs) hold promise for advanced electronics. However, discrepancies in reported electrical conductivities highlight the importance of measurement methodologies. This review explores intrinsic charge transport mechanisms and extrinsic factors influencing performance, and critically ...
Jonas F. Pöhls, R. Thomas Weitz
wiley +1 more source
MATEX: A Distributed Framework for Transient Simulation of Power Distribution Networks
, 2014 We proposed MATEX, a distributed framework for transient simulation of power distribution networks (PDNs). MATEX utilizes matrix exponential kernel with Krylov subspace approximations to solve differential equations of linear circuit.
Cheng, Chung-Kuan +3 more
core +1 more source
Advanced Functional Materials, EarlyView.The combination of formamidinium thiocyanate and 1,3‐propane diammonium iodide for bulk and top‐surface passivation, and a ternary fullerene blend to improve energy band alignment, suppresses energy losses in wide‐bandgap FAPbBr3 perovskite solar cells.
Laura Bellini +9 more
wiley +1 more source
An All‐Optical Driven Bio‐Photovoltaic Interface for Active Control of Live Cells
Advanced Functional Materials, EarlyView.Bio‐photovoltaic Interface (BIO‐PV‐I) for live cell manipulation is presented. BIO‐PV‐I can be activated non‐invasively and remotely to control the spatial motility, adhesion, and morphology of cells adhering to it. BIO‐PV‐I uses a patterned light‐induced electric potential in iron‐doped lithium niobate crystals whose light‐driven and reversible nature,
Lisa Miccio +8 more
wiley +1 more source
Novel Floating General Element Simulators Using CBTA [PDF]
, 2012 In this study, a novel floating frequency dependent negative resistor (FDNR), floating inductor, floating capacitor and floating resistor simulator circuit employing two CBTAs and three passive components is proposed.
Ayten, Umut Engin +3 more
core +1 more source
Advanced Functional Materials, EarlyView.A FeN4─O/Clu@NC‐0.1Ac catalyst containing atomically‐dispersed FeN4─O sites (medium‐spin Fe2+) and Fe clusters delivered a half‐wave potential of 0.89 V for ORR and an overpotential of 330 mV at 10 mA cm−2 for OER in 0.1 m KOH. When the catalyst was used in a rechargeable Zn–air battery, a power density of 284.5 mW cm−2 was achieved with excellent ...
Yongfang Zhou +8 more
wiley +1 more source
Melt Grafting of Geometry‐Tailored Voltage Stabilizers for High‐Performance Polypropylene Insulation
Advanced Functional Materials, EarlyView.A scalable one‐step melt grafting strategy is developed to enhance the dielectric properties of isotactic polypropylene by covalently incorporating thermally stable aromatic voltage stabilizers. This solvent‐free approach improves volume resistivity and DC breakdown strength through deep trap formation and charge localization, offering a sustainable ...
Nazirul Mubin bin Normansah +9 more
wiley +1 more source
Advanced Functional Materials, EarlyView.A vertically stacked, DEA‐driven photonic array inspired by cephalopod skin, featuring highly crystalline colloidal crystal gels with vivid color, low FWHM and scalability is presented. The multilayer design removes lateral pixel interference, achieving near‐100% fill factor with fully independent RGB actuation.
Maga Kim +11 more
wiley +1 more source
Advanced Functional Materials, EarlyView.Ferroelectricity in thin HfO2‐based films offers great possibilities for next‐generation neuromorphic memory devices. There, the response to subcoercive voltage signals is driven by the movement of mobile interfaces and their interaction with crystal defects – a yet rather unexplored aspect, which we shed light on and gain new insights into the complex
Maximilian T. Becker +11 more
wiley +1 more source
Advanced Functional Materials, EarlyView.An efficient NiOx HTL is successfully prepared by introducing MXene as an additive without further surface modification to fabricate high‐performance FASn0.5Pb0.5I3 perovskite solar cells. The introduction of MXene contributes to improved conductivity of NiOx, better aligned at NiOx/perovskite interfaces, and enhanced quality of perovskite films ...
Lijun Chen +12 more
wiley +1 more source