Results 181 to 190 of about 5,421,660 (323)

Optimized Time–Frequency Analysis for Induction Motor Fault Detection Using Hybrid Differential Evolution and Deep Learning Techniques

International Journal of Adaptive Control and Signal Processing, EarlyView.
Workflow of the parameter optimization process for ITSC fault detection, applying Differential Evolution optimization and the Smooth Pseudo Wigner‐Ville Distribution for signal processing. The optimized parameters are then used in the failure identification pipeline, which combines the signal processing with a YOLO‐based architecture for fault severity
Rafael Martini Silva, Avyner Lorran de Oliveira Vitor, Marcelo Favoretto Castoldi, Alessandro Goedtel, Wesley Angelino Souza   +4 more
wiley   +1 more source

Tribology of ZrC Coatings and Spherical Tips Acquired with Extraordinarily Stiff, Metal Atomic Force Microscopy Probes

Advanced Engineering Materials, EarlyView.
In this research, ZrC coatings are evaluated against various counterprobes at the microscale using novel super‐stiff atomic force microscopy cantilevers. The chemical composition of the coating is shown to be an important factor influencing coating hardness and Young's modulus, while surface roughness, counterprobe hardness, and surface energy are the ...
Piotr Jenczyk, Marcin Michałowski, Bogdan Warcholiński, Michał Milczarek, Adam Gilewicz   +4 more
wiley   +1 more source

Software and Data Citation [PDF]

, 2020
Clark, Tim, Fenner, Martin, Hong, Neil P Chue, Katz, Daniel S, Martone, Maryann E   +4 more
core  

Introducción y estudio comparativo de los nuevos indicadores de citación sobre revistas científicas en <i>Journal Citation Reports</i> y <i>Scopus</i>

, 2010
Daniel Torres‐Salinas, Evaristo Jiménez‐Contreras   +1 more
openalex   +2 more sources

A Simulative Approach for the Prediction of Mesoscale Residual Stress Fields in Solution‐Strengthened Ferritic Ductile Iron

Advanced Engineering Materials, EarlyView.
This study presents a 3D representative volume element‐based simulation approach to predict mesoscopic residual stress and strain fields in silicon solid solution‐strengthened ductile cast iron. By modeling phase transformation kinetics with an enhanced Johnson–Mehl–Avrami–Kolmogorov model, the effects of varying cooling rates on residual stresses are ...
Lutz Horbach, Oliver Schenk, Valérian Iss, Ali Rajaei, Jiali Zhang, Felix Weber, Christoph Broeckmann   +6 more
wiley   +1 more source

Influence of Heat Treatment on Microstructure and Mechanical Properties at Elevated Temperatures of Nonweldable Ni‐Based Alloy Printed by Fused Filament Fabrication

Advanced Engineering Materials, EarlyView.
The fused filament‐fabricated MAR‐M247 alloy without hot isostatic pressing shows the lowest porosity of 4%. Heat treatment at 1220 °C produces coarse precipitates and carbides. Specimens heat‐treated at 1220 °C exhibit higher tensile strength (683 MPa) and elongation (10%) at room temperature.
Haneen Daoud, Ying Zheng, Agata Kulig, Natalja Agarkov, Esma Mese, Wolfgang Hofmann, Peter Würtele, Uwe Glatzel   +7 more
wiley   +1 more source

Identifying Citation Classics in Fuzzy Decision Making Field Using the Concept of H-Classics

, 2014
Manuel J. Cobo, M. A. Martínez, María Gutiérrez-Salcedo, Manuel Herrera, Enrique Herrera‐Viedma   +4 more
openalex   +1 more source

Reliance on the citation index undermines the study of biodiversity [PDF]

, 2000
Antonio G. Valdecasas, Santiago Castroviejo, Leslie F. Marcus   +2 more
openalex   +1 more source

OpenDACHS: Ein Citation Repository zur nachhaltigen Archivierung zitierter Online-Quellen [PDF]

, 2020
Matthias Arnold, Hanno Lecher, Sebastian Vogt   +2 more
openalex   +1 more source

The TARCiS statement: Guidance on terminology, application, and reporting of citation searching [PDF]

, 2023
Julian Hirt, Thomas Nordhausen, Thomas Fuerst, Hannah Ewald, Christian Appenzeller‐Herzog   +4 more
openalex   +1 more source