Results 61 to 70 of about 12,846 (261)
Advanced Functional Materials, EarlyView.A 3D anisotropic hydrogel derived from heart extracellular matrix guides cytoskeletal alignment and nuclear remodeling in reprogrammed cardiomyocyte‐like cells. This study reveals how matrix alignment modulates nuclear envelope dynamics and chromatin state, triggering transcriptional and functional maturation.
Seung Ju Seo +7 more
wiley +1 more source
Research on cold rolling of 41Cr4/20NiCrMo7 bimetal composite bearing ring
Metalurgija, 2018 In order to improve the service life of bearing rings, a new method of cold rolling bimetal composite bearing rings was proposed in this paper.With Abaqus software,a finite element simulation model of the cold rolling of bimetal composite bearing rings ...
B. S. Sun, C. W. Wang, Z. L. Zhao
doaj
Materials and technology for fabricating mechanical connectors by cold plastic deformation
Transportation systems and technology, 2017 Formulation of the problem. Choice of materials and technologies for fabrication mechanical attached fittings (MAF) performed by cold plastic deformation. Method. Theoretical analysis based on mechanical properties fitting and tubing materials. Springback tubing materials shall exceed springback tubing materials. Results.
Yakov D Kogan, Natal'ya V Bogdanova
openaire +2 more sources
Advanced Functional Materials, EarlyView.ABSTRACT Electronic waste has emerged as a major environmental challenge, driven by the massive consumption and a limited lifetime of modern electronic devices, stimulating the development of sustainable electronics. Here, an all‐biomaterial gelatin‐choline‐citric acid ([Ch][CA]) ionogel is developed as an active binder to realize self‐sintered ...
Lin Guo +10 more
wiley +1 more source
Advanced Functional Materials, EarlyView.A soft, dual‐channel hydrogel patch enables simultaneous detection of wound temperature and strain by integrating ion‐diffusion‐mediated thermoelectric and resistive sensing. The conformal design maintains stable performance during motion, capturing subtle inflammatory and mechanical changes for continuous wound monitoring.
Yu Fang +7 more
wiley +1 more source
PROCESS PARAMETER MATCHING RESEARCH ON COMPOSITE STRENGTHENING OF TITANIUM ALLOY LUG STRUCTURAL
Jixie qiangdu, 2020 In order to improve the fatigue performance of the aviation lug structure,a finite element（FE） model of composite strengthening process which contains cold expansion and interference fit has been established.
CHANG YaNan +4 more
doaj
Fine-tuning of mechanical properties in a Zn-Ag-Mg alloy via cold plastic deformation process and post-deformation annealing. [PDF]
Bioact Mater, 2021 Wątroba M +3 more
europepmc +1 more source
Tuning Separator Chemistry: Improving Zn Anode Compatibility via Functionalized Chitin Nanofibers
Advanced Functional Materials, EarlyView.Nanochitin derived from waste shrimp shells is used to fabricate separators for aqueous zinc batteries. By tuning the density of amine and carboxylic surface groups, water mobility at the separator interface is controlled, promoting uniform zinc deposition, suppressing dendrite growth, and enabling exceptional cycling stability exceeding 2000 h ...
Ibrahim Al Kathemi +6 more
wiley +1 more source
Advances in Materials Science and Engineering, 2014 The paper presents a theoretical study on the compression of a two-layer strip of strain-hardening rigid-plastic materials between rigid platens. Semianalytical solutions are obtained for stress and velocity fields in each layer.
Sergei Alexandrov, Yusof Mustafa
doaj +1 more source
Advanced Functional Materials, EarlyView.Magnetic‐field‐assisted CVD of heterometallic single‐source precursors modulates thin‐film surface electronic structure and interfacial charge transfer. Field‐grown (Cobalt ferrite‐1T)CF‐1T films exhibit stabilized electronic states, lower kinetic barriers, and markedly enhanced nitrate‐to‐ammonia electrocatalysis versus (Cobalt ferrite‐0T) CF‐0T ...
Touraj Karimpour +11 more
wiley +1 more source