Results 11 to 20 of about 1,863 (256)
An Overview of Cold Spray Additive Technology in Australia for Melt-less Manufacture of Titanium [PDF]
MATEC Web of Conferences, 2020 The difficulty in significantly reducing the cost of titanium products is partly related to the high cost of manufacturing. This includes additive manufacturing; e.g.
Zahiri Saden H. +2 more
doaj +1 more source
Spray Deposition of Mechanically Alloyed F/M ODS Steel Powder [PDF]
Archives of Metallurgy and Materials, 2019 Thermal/cold spray deposition were used for additive manufacture of oxide dispersion strengthened (ODS) steel layers. Mechanically alloyed F/M ODS steel powders (Fe(bal.)-10Cr-1Mo-0.25Ti-0.35Y2O3 in wt.%) were sprayed by a high velocity oxygen fuel (HVOF)
Suk Hoon Kang +3 more
doaj +1 more source
Research Progress of Cold Spray and Its Application in Ship and Warship Fields [PDF]
Cailiao Baohu, 2022 Cold spray, as a low - temperature solid - state forming technology, has a series of advantages over other deposition methods, such as little heat influence towards substrate, minimized particle oxidation, and high deposition efficiency, and therefore it
XU Kang - wei, LUO Xiao - tao, WU Xiao - yu, XIE Shu - feng, HUANG Lei, SU Yao, TIAN Jia - jia
doaj +1 more source
Авіаційно-космічна техніка та технологія, 2020 Cold spray technology is a method of deposited metal coatings by high-speed particle impact, especially in the preparation of metal alloy materials (Cu alloys, Ti alloys, Al alloys, Ni-based alloys, Mg alloys, stainless steels, and high-temperature ...
Kun Tan +4 more
doaj +1 more source
Journal of the Mechanical Behavior of Materials, 2022 Cold spray process (CSP) is a thermal spray technology in which coating (10–40 µm) is formed in the solid state by the impingement of power particles with supersonic velocity (200–1,200 m/s2) on coupon employing compressed gas jet, below the melting ...
Ashokkumar Mohankumar +5 more
doaj +1 more source
A Review of Advances in Cold Spray Additive Manufacturing
Coatings, 2023 Cold Spray Additive Manufacturing (CSAM) produces freeform parts by accelerating powder particles at supersonic speed which, impacting against a substrate material, trigger a process to consolidate the CSAM part by bonding mechanisms. The literature has presented scholars’ efforts to improve CSAM materials’ quality, properties, and possibilities of use.
Rodolpho Vaz +4 more
openaire +3 more sources
Influence of Cold Spray Parameters on Bonding Mechanisms: A Review
Metals, 2021 The cold spray process is governed by the impact of high velocity feedstock particles onto a substrate without melting. Hence, the bulk material properties are retained. However, it is challenging to achieve good adhesion strength.
Surinder Singh +3 more
doaj +1 more source
Key role of temperature on delamination in solid-state additive manufacturing via supersonic impact
Materials Research Letters, 2023 Cold spray (CS) has emerged as a representative of solid-state additive manufacturing (AM) via supersonic impact. It enables a high deposition rate of solid-state microparticles.
Qian Wang +7 more
doaj +1 more source
Nanomechanical Characterization for Cold Spray: From Feedstock to Consolidated Material Properties
Metals, 2020 Cold gas-dynamic spray is a solid-state materials consolidation technology that has experienced successful adoption within the coatings, remanufacturing and repair sectors of the advanced manufacturing community.
Bryer C. Sousa +5 more
doaj +1 more source
Research progress on deposition mechanism of ceramic metallization by cold spraying
Fenmo yejin jishu, 2022 The difference in thermal expansion coefficient between ceramics and metals results in poor bonding strength after heat processing. Cold spraying (CS) is a new and green surface coating and additive manufacturing technology with the advantages as high ...
QIN Jia-hao +5 more
doaj +1 more source