Results 21 to 30 of about 1,863 (256)

Thermal Preprocessing of Rapidly Solidified Al 6061 Feedstock for Tunable Cold Spray Additive Manufacturing

Metals, 2022
In this work, the influence of thermal pre-processing upon the microstructure and hardness of Al 6061 feedstock powder is considered through the lens of cold spray processing and additive manufacturing.
Baillie Haddad, Bryer C. Sousa, Kyle Tsaknopoulos, Victor K. Champagne, Richard D. Sisson, Aaron Nardi, Danielle L. Cote   +6 more
doaj   +1 more source

Tailoring cold spray additive manufacturing of steel 316 L for static and cyclic load-bearing applications

Materials & Design, 2021
Thanks to the low working temperature, less product size limitations and one order of magnitude higher deposition rates compared to the established additive manufacturing techniques, more attention has been brought to the potential of cold spraying for ...
Sara Bagherifard, Jan Kondas, Stefano Monti, Jan Cizek, Fabrizio Perego, Ondrej Kovarik, Frantisek Lukac, Frank Gaertner, Mario Guagliano   +8 more
doaj   +1 more source

Cold spray under the banner of thermal spray in the whirlwind of additive manufacturing [PDF]

Surface Engineering, 2018
International ...
M. Jeandin, F. Delloro, P. E. Léger, V. Bortolussi, M. Sennour   +4 more
openaire   +4 more sources

Post-Processing of Cold Sprayed CoNiCrAlY Coatings on Inconel 718 by Rapid Induction Heating

Metals, 2022
Cold spray is a solid-state additive manufacturing process that has been increasingly used for restoration of damaged parts. Due to the nature of powder solid-state bonding, cold spray coatings usually possess pores in the microstructures. Heat treatment
Yongjing Yang, Aprilia Aprilia, Kaiqiang Wu, Sung Chyn Tan, Wei Zhou   +4 more
doaj   +1 more source

Research Progress of Cold Spraying High - Entropy Alloys [PDF]

Cailiao Baohu, 2022
High - entropy alloys are a kind of novel multi - principal component alloy that recently breaks through the design concept of traditional alloys, which were significantly superior to conventional metallic materials in compressive strength, hardness ...
FAN Ning - song, JIN Bing - qian, ZHANG Nan - nan, XIE Ying - chun, YIN Shuo
doaj   +1 more source

Microstructure and hardness comparison of as-built inconel 625 alloy following various additive manufacturing processes

Results in Materials, 2021
Experimental examples of as-built microstructures and associated microindentation hardnesses (HV) for a wide range of metal additive manufacturing (AM) processes for Inconel 625 alloy are presented in this research paper.
Ariel Gamon, Edel Arrieta, Paul R. Gradl, Colton Katsarelis, Lawrence E. Murr, Ryan B. Wicker, Francisco Medina   +6 more
doaj   +1 more source

Characteristics of Ti6Al4V Powders Recycled from Turnings via the HDH Technique

Metals, 2018
The objective of this research is for Ti6Al4V alloy turnings, generated during the machining of implants, to produce powders for the fabrication of Ti base coating via the cold spray method. In order to decrease the cost of powder production and increase
Mertol Gökelma, Dilara Celik, Onur Tazegul, Huseyin Cimenoglu, Bernd Friedrich   +4 more
doaj   +1 more source

REVIEW OF APPLICATION AND RESEARCH BASED ON COLD SPRAY COATING MATERIALS

Авіаційно-космічна техніка та технологія, 2021
Cold spray technology is an advanced spray technology, and its technical principle is the same as that of additive manufacturing technology. Cold spraying technology combines multiple advantages in the spraying field: not only can the deposition of thick
Kun Tan, Sergii Markovych, Wenjie Hu, Oleksandr Shorinov, Yurong Wang   +4 more
doaj   +1 more source

Microstructural evolutions and mechanical characteristics of Ti/steel clad plates fabricated through cold spray additive manufacturing followed by hot-rolling and annealing

Materials & Design, 2020
An innovative approach is designed to fabricate Ti/steel clad plates. Instead of using Ti sheets, pure Ti powder was initially deposited on steel plates using cold spray additive manufacturing (CSAM).
Zhipo Zhao, Naeem ul Haq Tariq, Junrong Tang, Cunlei Jia, Xiang Qiu, Yupeng Ren, Hanhui Liu, Yanfang Shen, Hao Du, Xinyu Cui, Jiqiang Wang, Tianying Xiong   +11 more
doaj   +1 more source

Current status and prospects of aviation remanufacturing technology based on cold spray

Hangkong gongcheng jinzhan
Cold spray additive manufacturing technology，with its unique "solid-state deposition" process characteristics，has shown great application potential in the repair and remanufacturing of damaged aerospace structures.
CHI Yada, CUI Minchao, LUO Ming, LI Wenya, ZHANG Dinghua   +4 more
doaj   +1 more source