Results 61 to 70 of about 54,430 (261)

Numerical investigation of oil shale combustion characteristics in a high-low differential velocity CFB boiler using the CPFD model [PDF]

Oil Shale
This study employs the computational particle fluid dynamic model to simulate a 65 t/h oil shale-fired high-low differential velocity circulating fluidized bed (CFB) boiler.
Hongpeng Liu, Xuexin Xiang, Shichao Li, Shuaishuai Cui, Chunxia Jia, Hong Qin, Qing Wang, Mingzhi Shan, Bin Liu, Wen Yang   +9 more
doaj   +1 more source

High Center‐of‐Mass, Multi‐Legged Soft Robots Powered by Geometrically Encoded Liquid Crystal Elastomer Arc Appendages

Advanced Materials, EarlyView.
Inspired by the octopus and the golden wheel spider, soft robots with liquid crystal elastomer arc fibers as appendages are fabricated to transcend surface constraints through an elevated center of mass and minimal contact footprints. By leveraging curvature‐encoded deformation‐recovery cycles, these robots exhibit contractile, torsional, and flexural ...
Jong Bin Kim, Antonio Proctor Martinez, Yaoye Hong, Ziyun Zhang, Kun‐Yu Wang, Shu Yang   +5 more
wiley   +1 more source

Influence of Carbon Nanoparticles on Electrically Induced Wear of Grease‐Lubricated Steels

Advanced Materials Interfaces, EarlyView.
When an electric current enters a pair of rubbing surfaces, enormous damage takes place. In this research, how such damage occurs in the presence of protective grease and the mitigation with added carbon nanoparticles, were investigated. It was discovered that those particles regulate transport and interfacial electrical stability of the grease ...
Mohammad Humaun Kabir, Darrius Dias, Jacob Bons, MD Wasek Foysal, Evan Johnson, Joe Kosmoski, Hong Liang   +6 more
wiley   +1 more source

Rotating Detonation Combustion Characteristics of Kerosene-Fueled Wide-Area Scramjets

气体物理
Through the method of three-dimensional numerical simulation, the rotating detonation combustion characteristics of kerosene-fueled scramjets in the range of Ma＝3~7 were studied. In the flight condition of Ma=3, due to the poor effect of fuel atomization
Chen SHU, Futao GU, Bin CHEN, Chenglong YAN, Yiheng TONG, Wei LIN   +5 more
doaj   +1 more source

Thermal Radiation Emission From 3D Graphene Networks

Advanced Materials Interfaces, EarlyView.
Three‐dimensional graphene networks are demonstrated as exceptional broadband thermal emitters, exhibiting high‐intensity, spectrally homogeneous emission and strong mechanical flexibility compared to conventional emitters like silicon carbide.
Maria Chiara Paolozzi, Emanuele Scoppi, Jacopo Sera, Salvatore Macis, Antonio Grilli, Samuel Jeong, Yoshikazu Ito, Stefano Lupi   +7 more
wiley   +1 more source

Combustion And Emission Characteristics In A Can-Type Combustion Chamber

, 2014
Combustion phenomenon will be accomplished effectively by the development of low emission combustor. One of the significant factors influencing the entire Combustion process is the mixing between a swirling angular jet (Primary Air) and the non-swirling inner jet (fuel).
Selvakuma Kumaresh, Kim, Man Young
openaire   +2 more sources

Combustion characteristics of catalytically supported thermal combustion systems

, 2022
A widely applied thermal theory, one of the first flame propagation theories, implies that combustion proceeds primarily at temperatures close to the maximum the flame can achieve. A set of differential equations developed for thermal conductivity and diffusion is reduced to one equation that yields the burning velocity value.
openaire   +1 more source

From the Discovery of the Giant Magnetocaloric Effect to the Development of High‐Power‐Density Systems

Advanced Materials Technologies, EarlyView.
The article overviews past and current efforts on caloric materials and systems, highlighting the contributions of Ames National Laboratory to the field. Solid‐state caloric heat pumping is an innovative method that can be implemented in a wide range of cooling and heating applications.
Agata Czernuszewicz, Yaroslav Mudryk, Jun Cui, Lucas Griffith, Duane D. Johnson, Julie Slaughter   +5 more
wiley   +1 more source

Additively Manufactured Porous Ceramics as Tunable Dielectrics for Passive Temperature Sensing

Advanced Materials Technologies, EarlyView.
Porous ceramic lattices, 3D‐printed from a multicomponent oxide ink, are integrated with LC resonators for passive wireless temperature sensing. By tuning porosity, the dielectric properties and RF response are engineered to produce distinct resonant frequency shifts with temperature. The results establish a structure‐driven approach to customizing the
Sogol Heidarishahrivar, Aminul Islam, Chang Woo Gal, Insup Kim, Yeong‐Jin Choi, Woo Soo Kim   +5 more
wiley   +1 more source

Record Performance in Vertically Stacked, Solution‐Processed ZTO Schottky Diodes

Advanced Materials Technologies, EarlyView.
Schottky diodes based on solution processed sustainable zinc—tin–oxide thin films present an eco‐friendly and versatile alternative to conventional CMOS based technologies. Beyond state‐of‐the‐art performance for vertically stacked solution‐based oxide diodes was achieved, including rectification ratios exceeding nine orders of magnitude, and intrinsic
Carlos Silva, Asal Kiazadeh, Raquel Azevedo Martins, António Dias, Jorge Martins, Luís Mendes, João Vaz, Rodrigo Martins, Elvira Fortunato, Emanuel Carlos, Jonas Deuermeier   +10 more
wiley   +1 more source