Results 41 to 50 of about 1,282,378 (244)

Particle‐Level ZrO2 Atomic Layer Deposition Enables Fast‐Cycling and Long‐Life Graphite Cathodes for Dual‐Ion Batteries

open access: yesAdvanced Functional Materials, EarlyView.
A spatial location of atomic layer deposition (ALD)‐derived ZrO2 coatings is demonstrated to be a critical design parameter for stabilizing graphite cathodes in DIBs. Direct particle‐level ALD (PALD) screening of representative metal oxides identified ZrO2 as the coating that provides the most favorable balance of high‐rate capability and interfacial ...
Jieun Kang   +7 more
wiley   +1 more source

Compacted and spheroidal graphite irons: Experimental evaluation of Poisson's ratio [PDF]

open access: yesFME Transactions, 2016
Spheroidal Graphite cast Iron (SGI), also known as ductile iron, represents a perfect material for a very large range of modern applications. It is successfully used wherever optimal strength, stiffness and even low costs are required: high values of ...
Fragassa Cristiano, Pavlović Ana
doaj  

Selective Laser Sintering and Graphitization for Mono‐Matrix Unibody Fabrication of Integrated Stereo‐Circuit and Stereo‐Fluidic Wearable Electronics

open access: yesAdvanced Materials, EarlyView.
A novel selective laser sintering and graphitization (SLSG) 3D printing technology enables unibody fabrication of compacted insulating structures and conductive circuits in fluidic‐integrated wearable electronics through adaptive photonic modulation.
Li Zhang, Wing Cheung Mak
wiley   +1 more source

Solidification and Room Temperature Microstructure of a Fully Pearlitic Compacted Graphite Cast Iron [PDF]

open access: yes, 2018
Compacted graphite cast irons are rapidly developing for they have better mechanical properties than lamellar graphite cast irons and present less porosity than spheroidal graphite cast irons.
Freulon, Alexandre   +2 more
core   +1 more source

Structural and Phase Analysis of the Ausferritic Ductile Cast Iron Matrix Obtained by Heat Treatment and in the Raw State

open access: yesC
This paper presents a comparative analysis of ausferritic ductile cast iron matrix obtained through heat treatment and in its raw state. Ausferrite without heat treatment was achieved by modifying the chemical composition, while nodular graphite was ...
Leszek Klimek   +4 more
doaj   +1 more source

Investigation of Drilling Machinability of Compacted Graphite Iron under Dry and Minimum Quantity Lubrication (MQL)

open access: yesMetals, 2019
Compacted graphite iron (CGI), which is used as a potential material in the auto industry, is a hard-to-machine material for the different minor elements and for the geometry of graphite with grey cast iron.
Yang Li, Wenwu Wu
doaj   +1 more source

Biomass DNA: An Emerging Building Block for Advanced Materials

open access: yesAdvanced Materials, EarlyView.
Biomass DNA is rapidly emerging from its traditional role as a genetic blueprint to serve as a versatile abundant, highly programmable polymeric building block. This review highlights the transformation of macroscopic bulk biomass DNA into next generation of functional materials, spanning from dynamic hydrogels, sustainable bioplastics, and high ...
Yuwei Hu, Itamar Willner, Li Niu
wiley   +1 more source

Compacted Graphite Iron with the Addition of Tin [PDF]

open access: yes, 2020
The paper presents the effect of tin on the crystallization process, microstructure and hardness of cast iron with compacted (vermicular) graphite. The compacted graphite was obtained with the use of magnesium treatment process (Inmold technology).
Gumienny, G., Kurowska, B., Fabian, P.
core  

Effect of mould inoculation on formation of chunky graphite in heavy section spheroidal graphite cast iron parts [PDF]

open access: yes, 2007
The manufacturing process of heavy section ductile iron castings is strongly influenced by the risk of graphite degeneration under slow cooling rates.
Asenjo, Iker   +6 more
core   +1 more source

Understanding and Designing Phase Change Materials: Insights From Atom Probe Tomography

open access: yesAdvanced Science, EarlyView.
Atom probe tomography can distinguish metallic, covalent, and metavalent bonds based upon their bond rupture; in particular, the probability to form more than one ion (PME) in laser‐assisted field evaporation. These findings open new avenues in understanding and designing phase change materials (PCMs) since they allow quantification of bonds in solids ...
Jan Köttgen   +3 more
wiley   +1 more source

Home - About - Disclaimer - Privacy