Results 91 to 100 of about 1,861,033 (245)

Review on Composite Joints for Cold-Formed Steel Structures

E3S Web of Conferences, 2018
Introduction of the lightweight cold-formed steel (CFS) sections to building construction has been well-established these days due to its high structural performance, corrosion resistance, ease of construction and maintenance as well as aesthetic ...
Amsyar Faisal, Tan Cher Siang, Ma Chau Khun, Sulaiman Arizu   +3 more
doaj   +1 more source

Cryogenic Deformation Behavior of TiAl and Insights Into Embrittlement After High‐Temperature Exposure Combined With Secondary Ion Mass Spectroscopy of Near Surface Chemistry

Advanced Engineering Materials, EarlyView.
Near‐surface deuterium enrichment profiles for different microstructural types of TiAl after exposure at 700 °C in a heavy water‐containing environment. The deuterium levels are significantly higher than expected from natural occurrence, indicating that the heavy water dissociated during the exposure treatment and entered the specimens.
Jonathan D. H. Paul, Alexander Welle, Dirk Matthiessen, Michael Oehring, Fritz Appel, Florian Pyczak   +5 more
wiley   +1 more source

NON-LINEAR ANALYSIS OF CONTINUOUS COMPOSITE CONCRETE–STEEL BEAMS UNDER CYCLIC LOADINGS

Diyala Journal of Engineering Sciences, 2011
Non-linear analysis of continuous composite concrete–steel beams under cyclic loadings has been investigated in this paper. A three-dimensional finite element analysis (FE) ANSYS computer program(ANSYS version 9.0) was conducted to investigate the ...
Ali Laftah Abbas
doaj   +1 more source

Enhancement of the Through‐Thickness Electrical Conductivity of Carbon‐Fiber‐Reinforced Plastics Using Large Graphite Particles

Advanced Engineering Materials, EarlyView.
To enhance through‐thickness conductivity without sacrificing impregnation, large spherical graphite particles are intentionally employed in a low‐viscosity resin. Unlike finer conductive fillers, these particles remain outside the fiber bundles and accumulate in resin‐rich interlaminar regions during molding.
Keito Hosoe, Yu Zhou, Shintaro Kamiyama, Takao Okada, Tomohiro Yokozeki, Ryoma Tokonami, Tatsuhiro Takahashi   +6 more
wiley   +1 more source

Composite Beam Under Different Monotonic and Dynamic Loading: A Review

Journal of Engineering and Sustainable Development
In the modern world, composite construction is widely used due to its exceptional properties in reducing the structure's weight and carrying load. This paper reviews some researchers' earlier investigations in the past two decades.
Ayad Hasan Jawad, Hesham A.Numan
doaj   +1 more source

3D‐Printed Titanium Gyroid Scaffold Structure Integrated With Tough Hybrid Materials for Cartilage Replacement

Advanced Engineering Materials, EarlyView.
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin, Gloria R. Young, Francesca Tallia, Reece N. Oosterbeek, Shaaz Ghouse, Edward Spiers, Nupur Kohli, Tom Briggs, Marc Masen, Siwei Li, Ren‐Jei Chung, Jonathan R. T. Jeffers, Julian R. Jones   +12 more
wiley   +1 more source

Coupled Modal Analysis and Aerodynamics of Rotating Composite Beam. [PDF]

Materials (Basel), 2023
Stachyra G, Kloda L, Szmit Z.
europepmc   +1 more source

The Role of Ultra‐Thin Passive Films and Organic Adsorbates on Aluminum Chips for a Friction‐Induced Solid‐State Recycling Process

Advanced Engineering Materials, EarlyView.
Despite benefits to storage stability and handleability of aluminum scrap, octadecyl phosphonic acid (ODPA) SAMs reduce the tensile strength of wires produced using friction‐induced recycling. Etching and methyl diphosphonic acid (MDPA) coatings, however, have little effect.
Timothy D. Goller, Steffen Gabsa, Werner Homberg, Guido Grundmeier   +3 more
wiley   +1 more source

Experimental Analysis of Eccentric Compression Performance of Larch Wood-Steel Composite Columns

Advances in Civil Engineering, 2019
In this paper, a new steel-wood composite column with an H-shaped section was proposed. In order to form an H-shaped cross section, a larch board is fixed on the outer surface of the left and right edges of a hot-rolled H-beam by using physical ...
Junren Wang, Shaowei Duan, Jiewei He, Zhifeng Wang   +3 more
doaj   +1 more source

Elastic–Plastic Modeling and Experimental Characterization of Granular Jamming Actuators

Advanced Engineering Materials, EarlyView.
Granular jamming enables rapid switching between soft and rigid mechanical states. Here, a reduced‐order elastic‐perfectly‐plastic beam framework captures pressure‐dependent loading, unloading, residual deformation, and hysteresis in jammed beams, while matching three‐point bending experiments across materials and geometries. The framework links design
Saheli Patel, Prashant K. Purohit, Jordan R. Raney   +2 more
wiley   +1 more source