Results 51 to 60 of about 22,268 (218)
Arthritis Care &Research, Accepted Article.Objective High body mass index (BMI≥27 kg/m2) and aberrant gait biomechanics are primary risk factors for knee osteoarthritis (KOA), yet the specific loading patterns linked to clinical disease features remain unclear. Unsupervised machine learning (ML) was used to identify vertical ground reaction force (vGRF) waveform modes of variation and ...
Ashley N. Buck +10 more
wiley +1 more source
Arthritis Care &Research, Accepted Article.Objectives This study synthesised the content and reporting completeness of published physical therapist‐led interventions for glenohumeral osteoarthritis (GHOA). Methods This systematic review undertook electronic database searches in PubMed, EMBASE, Cochrane, CINAHL and PEDro (until June 2025) for any peer‐reviewed articles/studies describing ...
Daha G Muhammad +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar +2 more
wiley +1 more source
Advanced Nonlinear StudiesThis paper concerns the long time existence of the smooth solutions of the compressible Euler system with critical time-dependent damping in R 2. We establish the sharp lifespan estimate from below, with respect to the small parameter of the initial ...
Cai Lv +3 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.A numerical–experimental framework is developed for characterizing multi‐matrix fiber‐reinforced polymers (MM‐FRPs) combining epoxy and polyurethane matrices. Harmonic bending tests are integrated with finite element model updating (FEMU) to simultaneously identify elastic and viscoelastic material parameters.
Rodrigo M. Dartora +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
PLoS ONE, 2020 Over exploitation of groundwater in Changping District of Beijing city has caused serious land subsidence in the past decades. In recent years, the operation of the South-to-North Water Transfer Project has reduced the land subsidence rate. In this paper,
Yanbo Cao +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study examines how helicoidal architectures with different porosities respond to bending. Adjusting layer angle and spacing in 3D‐printed polymers reveals clear tradeoffs between stiffness, strength, and energy absorption. Experiments and simulations highlight designs that distribute stress effectively, offering pathways for optimizing lightweight
Praveenkumar Subhash Patil +2 more
wiley +1 more source