Results 81 to 90 of about 329,381 (307)
3D FEA modelling of laminated composites in bending and their failure mechanisms [PDF]
, 2014 keywords: 3D keywords: 3D keywords: 3D keywords: 3D keywords: 3DAbstract This paper developed three-dimensional (3D) Finite Element Analysis (FEA) to investigate the effect of fibre lay-up on the initiation of failure of laminated composites in bending ...
Berbinau +35 more
core +2 more sources
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Frontiers in Materials, 2020 Compressive strength is probably one the most crucial properties of concrete material. For existing structures, core samples are drilled and tested to obtain the concrete compressive strength.
Yu Ren Wang, Yen Ling Lu, Dai Lun Chiang
doaj +1 more source
Stress-strain response and microstructural evolution of a FeMnCAl TWIP steel during tension-compression tests [PDF]
, 2016 © 2016. The stress-strain response of a Fe-17.5Mn-0.7C-2Al TWIP steel during cyclic loading has been investigated by means of tension-compression tests within the strain limits of ±2%, ±5% and ±10%. In addition, the microstructural evolution during the ±
Benito Páramo, José Antonio +3 more
core +2 more sources
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
A study of Compressive Strength Characteristics of Laterite/sand Hollow Blocks [PDF]
, 2007 This paper presents the results of experimental investigations carried out on partial replacement of sand with laterite as it affects the compressive strength of sandcrete hollow blocks. Two mix proportions (1:6 and 1:8) were used with laterite content
Ata, Olugbenga +3 more
core +1 more source
Advanced Engineering Materials, EarlyView.Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar +2 more
wiley +1 more source
Probe penetration test applied for evaluating shotcrete compressive strength
Revista IBRACON de Estruturas e MateriaisThis study presents a methodology for evaluating shotcrete compressive strength. Because of the high surface roughness and low thickness of the concrete layer observed in shotcrete structures, the proposed methodology is based on the probe penetration ...
W. R. L. da Silva +2 more
doaj +1 more source
Modified Glass Ionomer Cement with “Remove on Demand” Properties: An In Vitro Study
Dentistry Journal, 2017 Objectives: To investigate the influence of different temperatures on the compressive strength of glass ionomer cement (GIC) modified by the addition of silica-coated wax capsules; Material and Methods: Commercially-available GIC was modified by adding ...
Shaza Bishti +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source