Results 91 to 100 of about 55,674 (265)

Characterization of Defect Distribution in an Additively Manufactured AlSi10Mg as a Function of Processing Parameters and Correlations with Extreme Value Statistics

Advanced Engineering Materials, EarlyView.
Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt, Varma Kvvssn, Hossein Laieghi, Zia Uddin, Peyman Ansari, E. Kıvanç Sadak, Can Barış Toprak, Hüseyin Kızıl, Enrico Salvati   +8 more
wiley   +1 more source

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

Advanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi, Pasquale Guglielmi, Gianfranco Palumbo, Giuseppe Carbone   +3 more
wiley   +1 more source

Laser Powder Bed Fusion of Alumina: Effects of Scanning Strategies on External and Internal Defects

Advanced Engineering Materials, EarlyView.
This study investigates how scanning strategies affect pure alumina in laser powder bed fusion. Linear 45° scanning yields uniform surfaces but high porosity, while the island‐concentric strategy provides higher density with through‐holes favorable for infiltration. Findings highlight pathways toward optimizing defect‐free alumina parts.
Mohamed Abdelmoula, Gökhan Küçüktürk, Duran Kaya, David Grossin, Christophe Tenailleau, Benjamin Duployer, Enrique Juste, Fabrice Petit   +7 more
wiley   +1 more source

Planar Solid‐State Nanopores Toward Scalable Nanofluidic Integration Based on CMOS Technology

Advanced Engineering Materials, EarlyView.
We present a scalable silicon‐based fabrication strategy for planar solid‐state nanopores to enable their integration with complex nanofluidic systems. Prototype devices demonstrate normal voltage‐current characteristics, good noise performance, and appreciable streaming currents. Our CMOS‐compatible fabrication process offers precise geometric control
Ngan Hoang Pham, Chenyu Wen, Mohammad Hadi Khaksaran, Won‐Yong Lee, Javier Cruz, Klas Hjort, Dongping Wu, Shi‐Li Zhang   +7 more
wiley   +1 more source

Tailored Hierarchical Porous Copper Architectures via Three Dimensional Printing and Pressure‐less Sintering for Next‐Generation Lithium‐Metal Batteries

Advanced Engineering Materials, EarlyView.
A hierarchical porous copper current collector is fabricated via three‐dimensional printing combined with pressureless sintering to stabilize lithium metal anodes. The interconnected architecture lowers local current density, guides uniform Li deposition within pores, and suppresses dendrite growth.
Alok Kumar Mishra, Mukul Shukla
wiley   +1 more source

Optimal waveguide structure for low-threshold InGaN/GaN-based photonic-crystal surface-emitting lasers

AIP Advances
We analyzed the optimal waveguide structure of two types of InGaN-based photonic crystal surface-emitting lasers (PCSELs) to suppress the coupling with leaky modes via mode simulations.
Wen-Hsuan Hsieh, Duan-Hsin Huang, Tien-Chiu Chen, Po-Yang Chang, Tien-Chang Lu, Chia-Yen Huang   +5 more
doaj   +1 more source

Evaluating Energy Absorption Performance of Filled Lattice Structures

Advanced Engineering Materials, EarlyView.
Maximum stress must be considered to robustly evaluate energy absorber designs. This approach was applied to compare all types of absorbers in a single Ashby diagram and determine the utility of filling lattice voids with a second material. High‐performance fillers can improve the performance of lattices that are limited by buckling or catastrophic ...
Christian Bonney, William P. King, Iwona Jasiuk   +2 more
wiley   +1 more source

Research on confinement improvement under rational safety factor q on EAST

AIP Advances
The q(r) profile distribution is a critical issue for the confinement and stability of the plasma. The optimized q(r) profiles can help reduce magnetic disturbances in the magnetic field, reduce the particle and energy loss of the plasma, inhibit the ...
Z. H. Wang, F. F. Long, B. Zhang, Z. X. Liu, X. Z. Gong, J. P. Qian, G. Q. Li, X. M. Zhong, W. Wang, Y. T. Guo, Q. Zang, S. X. Wang, Z. C. Lin   +12 more
doaj   +1 more source

Effect of the transverse reinforcement spacing in nodal zones on the seismic behavior factor of RC frames according to Algerian design code RPA99/version2003

Journal of Building Materials and Structures
The seismic behavior of reinforced concrete (RC) frames is significantly influenced by the confinement provided by transverse reinforcement. This study investigates the effect of transverse reinforcement spacing on the seismic behavior factor (R) of ...
Amar Louzai , Ahmed Abed
doaj   +1 more source

Towards Defect Phase Diagrams: From Research Data Management to Automated Workflows

Advanced Engineering Materials, EarlyView.
A research data management infrastructure is presented for the systematic integration of heterogeneous experimental and simulation data required for defect phase diagrams. The approach combines openBIS with a companion application for large‐object storage, automated metadata extraction, provenance tracking and federated data access, thereby supporting ...
Khalil Rejiba, Sang‐Hyeok Lee, Christina Gasper, Martina Freund, Sandra Korte‐Kerzel, Ulrich Kerzel   +5 more
wiley   +1 more source