Results 61 to 70 of about 292 (231)

Slip Localization Intensification Mediated by Grain Boundary Sliding in a Polycrystalline Nickel‐Based Superalloy

Advanced Engineering Materials, EarlyView.
The temperature dependence of fatigue behavior in nickel‐based superalloys is investigated through high‐resolution measurements of plastic localization. While increasing temperature reduces localization and enhances fatigue performance in René 88DT, Inconel 718 exhibits a sharp degradation at intermediate temperature due to intensified slip ...
M. Calvat, D. Anjaria, I. Woo, C. Bean, D. Texier, J. C. Stinville   +5 more
wiley   +1 more source

Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy

Advanced Engineering Materials, EarlyView.
A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang, Aparajita Pramanik, Sandipan Sen, Shubhashis Dixit, Marcel Muench, R. J. Vikram, Daniel Schliephake, Yolita M. Eggeler, Ankur Chauhan, Martin Heilmaier, Alexander Kauffmann   +10 more
wiley   +1 more source

High‐Temperature Nanoindentation of Metals: Assessing Thermal Drift, Frame Compliance, and Chemical Composition Effects on the Reported Mechanical Properties

Advanced Engineering Materials, EarlyView.
Do not let thermal drift and instrument artifacts deceive high‐temperature nanoindentation results. We compare classical Oliver–Pharr and automatic image recognition analyses across steels and a Ni alloy to quantify these effects. Accounting for artifacts reveals systematic softening with temperature, while Cr and Ni additions boost resistance ...
Velislava Yonkova, Steffen Brinckmann, Ruth Schwaiger   +2 more
wiley   +1 more source

Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites

Advanced Engineering Materials, EarlyView.
Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter, Andreas Bezold, Johan Westraadt, Katharina Fiegl, Subham Chattoraj, Benjamin Wahlmann, Carolin Körner, Michael Mills, Mathias Göken, Steffen Neumeier   +9 more
wiley   +1 more source

Workflow for Design of Experiments‐Based Modeling of Species Transport and Growth Kinetics in GaN Hydride Vapor Phase Epitaxy

Advanced Engineering Materials, EarlyView.
A novel workflow for investigating hydride vapor phase epitaxy for GaN bulk crystal growth is proposed. It combines Design of experiments (DoE) with physical simulations of mass transport and crystal growth kinetics, serving as an intermediate step between DoE and experiments.
J. Tomkovič, G. Lukin, H. Torkashvand, A. Kerschbaum, M. Müller, S. Besendörfer, J. Heitmann, J. Friedrich   +7 more
wiley   +1 more source

Enhanced Strength and Corrosion Resistance of Ti‐13Nb‐12Ta‐10Zr‐4Sn Alloy by Aging Treatment

Advanced Engineering Materials, EarlyView.
This work systematically investigates the effect of aging treatment on mechanical properties and corrosion behavior of vacuum arc‐melted Ti‐13Nb‐12Ta‐10Zr‐4Sn alloy. Owing to the increased α″ martensite, strength and corrosion resistance were significantly enhanced by aging treatment.
Yuhua Li, Rong Zhao, Qian Zhang, Haojie Wang, Yujing Liu, Lai‐Chang Zhang   +5 more
wiley   +1 more source

Evaluation of Plasticity and Creep Parameters From Tensile Stress–Strain Data for a Range of Strain Rates

Advanced Engineering Materials, EarlyView.
This plot compares experimental tensile stress–strain curves (with 4 different strain rates) and corresponding modelled curves (obtained using the optimised sets of Voce and Miller–Norton parameter values shown). The inferred M‐N values, characterizing the creep, are very similar to those obtained via conventional creep testing.
S. Ooi, R. P. Thompson, T. W. Clyne
wiley   +1 more source

New Construction Laws

International Journal of Public Administration, Management and Economic Development
The new Construction Act became the object of interest of many lawyers and representatives of towns and municipalities. Despite many amendments, the original Construction Act is outdated, cumbersome and inflexible, and along with it, the Act on Spatial Planning and Amendments to certain Acts is changing.
Mária Kováčová, Andrea Čajková
openaire   +1 more source

In Situ Micromechanical Study of Bimodal γ′–γ″ Precipitate Assemblies in Ni–Cr–Al–Nb Superalloy

Advanced Engineering Materials, EarlyView.
A Ni–Cr–Al–Nb superalloy with a bimodal γ′–γ″ precipitate distribution is developed. Composite precipitate assemblies form through heterogeneous nucleation, effectively impeding dislocation motion. Micropillar compression reveals high strength at room and elevated temperatures, governed by precipitate shearing, with coupled faulting mechanisms ...
Ujjval Bansal, Tae‐Hyeok Kang, Pyuck‐Pa Choi, Subin Lee, Christoph Kirchlechner   +4 more
wiley   +1 more source

Toward Knowledge‐Based Workflows: A Semantic Approach to Atomistic Simulations for Mechanical and Thermodynamic Properties

Advanced Engineering Materials, EarlyView.
Knowledge‐based atomistic workflows are presented for mechanical and thermodynamic properties. By coupling modular simulations with ontology‐aligned metadata and provenance, Fe case studies on elastic behavior, defects, thermal properties, and Hall–Petch strengthening reveal how FAIR, queryable, and reusable simulation data can be generated. Mechanical
Abril Azócar Guzmán, Hoang‐Thien Luu, Sarath Menon, Tilmann Hickel, Nina Merkert, Stefan Sandfeld   +5 more
wiley   +1 more source