Results 21 to 30 of about 297,484 (197)

Does Long‐Term Lower Extremity Strength Training in Adults With Knee Osteoarthritis and Varus Alignment Reduce Knee Joint Loading During Gait?

Arthritis Care &Research, EarlyView.
Objective We examined whether 18 months of strength training in individuals with knee varus alignment and medial tibiofemoral osteoarthritis (OA) reduced knee joint loads during walking compared to an attention control group. Methods This study was a secondary analysis of a randomized clinical trial that compared the effects of strength training to a ...
Stephen P. Messier, Matthew N. Vigliotti, Paige E. Rice, Brian Pietrosimone, Shannon L. Mihalko, Edward H. Ip, Richard F. Loeser, David J. Hunter, Ali Guermazi, Ryan Hill, Santiago Saldana, Kim L. Bennell, Paul DeVita   +12 more
wiley   +1 more source

Triangular Index Ratio as an Alternative Method to the Alpha Angle for Defining the Presence of Cam Morphology: A Prospective Cohort Study

Arthritis Care &Research, EarlyView.
Objective Cam morphology, which is a significant risk factor for hip osteoarthritis, is commonly quantified by the alpha angle (AA). This study aims to explore the potential of the triangular index ratio (TIR) to quantify cam morphology on anteroposterior radiographs by assessing the association between TIR‐defined cam morphology and the development of
Jinchi Tang, Fleur Boel, Michiel M. A. van Buuren, Noortje S. Riedstra, Myrthe A. van den Berg, Jos Runhaar, Sita Bierma‐Zeinstra, Rintje Agricola   +7 more
wiley   +1 more source

Pain and Patient‐Reported Physical Function Did Not Differ Among Body Composition Profiles in Patients With Hip Osteoarthritis

Arthritis Care &Research, EarlyView.
Objective To explore whether higher body fat and lower lean mass are associated with greater pain and worse patient‐reported physical function in individuals with hip osteoarthritis (OA). A secondary aim was to examine whether pain and patient‐reported physical function differ according to four body composition profiles: high body fat, low lean mass ...
Alexandra Ryan, Boliang Wang, Fiona Dobson, Ben Kirk, Travis Haber, Kim L. Bennell, Shirley P. Yu, Kim Allison, Ricardo J. S. Costa, Gabrielle Knox, Michelle Hall   +10 more
wiley   +1 more source

Carboxylic‐Acid Functionalized Multiwalled Carbon Nanotube‐Alkane‐Based Resistive Temperature Sensor for Cold Chain Applications

Advanced Engineering Materials, EarlyView.
This study presents a reversible temperature sensor with high switching ratio, ∼103. The device is fabricated using PET‐ITO and carbon nanotube dispersions in alkane. Considering its application in cold chain logistics, a proof‐of‐concept with LED is showcased. Thus, a temperature drop below the threshold temperature (crystallization temperature of the
Sunil Kumar Behera, Philippe Marrec, A. Jorge Parola, Madalena Dionísio, Hugo Águas, Andreia F. M. Santos, Hamed Pourkheirollah, Donald Lupo, César A. T. Laia   +8 more
wiley   +1 more source

Planar Solid‐State Nanopores Toward Scalable Nanofluidic Integration Based on CMOS Technology

Advanced Engineering Materials, EarlyView.
We present a scalable silicon‐based fabrication strategy for planar solid‐state nanopores to enable their integration with complex nanofluidic systems. Prototype devices demonstrate normal voltage‐current characteristics, good noise performance, and appreciable streaming currents. Our CMOS‐compatible fabrication process offers precise geometric control
Ngan Hoang Pham, Chenyu Wen, Mohammad Hadi Khaksaran, Won‐Yong Lee, Javier Cruz, Klas Hjort, Dongping Wu, Shi‐Li Zhang   +7 more
wiley   +1 more source

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

Advanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo, Shuo Qu, Shiming Gao, Xu Song   +3 more
wiley   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Effect of Oxygen Content on Surface and Subsurface Integrity During Turning of Ti–6Al–4V

Advanced Engineering Materials, EarlyView.
This study examines how oxygen content in the ambient atmosphere affects the surface and subsurface properties of Ti–6Al–4V during turning. Results show that oxygen does not influence surface roughness. However, machining in an extremely high vacuum‐adequate atmosphere increases surface hardness by up to 7.8% and induces compressive residual stresses ...
Benjamin Bergmann, Berend Denkena, Hilke Petersen, Florian Schaper   +3 more
wiley   +1 more source

Oxide‐Free Titanium Coatings by Wire Arc Spraying in a Silane‐Doped Inert Atmosphere

Advanced Engineering Materials, EarlyView.
A silane‐doped argon atmosphere enables the production of oxide‐free titanium coatings via twin‐wire arc spraying at ambient pressure. This innovative approach eliminates residual oxygen, creating process conditions that prevent oxidation and nitride formation.
Manuel Rodriguez Diaz, Maik Szafarska, René Gustus, Kai Möhwald, Hans Jürgen Maier   +4 more
wiley   +1 more source

Near‐Field Electrospinning Micro‐Printhead Achieves Precise Control of Nanofiber Deposition

Advanced Engineering Materials, EarlyView.
A micro‐printhead for near‐field electrospinning enables reproducible deposition of polymer nanofibers with diameters below 50 nm. Systematic parameter studies uncover the mechanisms linking operating conditions to fiber morphology, paving the way for precise and low‐cost nanoscale 3D manufacturing.As a high‐resolution, cost‐effective, and rapid ...
Han Xu, Dario Mager, Jan G. Korvink
wiley   +1 more source