Results 61 to 70 of about 111,096 (262)

Tailored Hierarchical Porous Copper Architectures via Three Dimensional Printing and Pressure‐less Sintering for Next‐Generation Lithium‐Metal Batteries

Advanced Engineering Materials, EarlyView.
A hierarchical porous copper current collector is fabricated via three‐dimensional printing combined with pressureless sintering to stabilize lithium metal anodes. The interconnected architecture lowers local current density, guides uniform Li deposition within pores, and suppresses dendrite growth.
Alok Kumar Mishra, Mukul Shukla
wiley   +1 more source

Radiographic evaluation of root canal cleaning, main and laterals, using different methods of final irrigation

Revista de Odontologia da UNESP
OBJECTIVE: To evaluate the efficacy of passive ultrasonic irrigation (PUI) using intermittent or continuous flushing and conventional manual irrigation (CMI) on the cleaning of main and simulated lateral root canals.MATERIAL AND METHOD: The root canals ...
Gisselle Moraima CHÁVEZ-ANDRADE, Juliane Maria GUERREIRO-TANOMARU, Lucas Martinati MIANO, Renato de Toledo LEONARDO, Mario TANOMARU-FILHO   +4 more
doaj   +1 more source

Near‐Field Electrospinning Micro‐Printhead Achieves Precise Control of Nanofiber Deposition

Advanced Engineering Materials, EarlyView.
A micro‐printhead for near‐field electrospinning enables reproducible deposition of polymer nanofibers with diameters below 50 nm. Systematic parameter studies uncover the mechanisms linking operating conditions to fiber morphology, paving the way for precise and low‐cost nanoscale 3D manufacturing.As a high‐resolution, cost‐effective, and rapid ...
Han Xu, Dario Mager, Jan G. Korvink
wiley   +1 more source

Co-op clean-up to continue, president

, 2018
Coverage ...
openaire   +4 more sources

Mathematical model of a root harvester after-cleaning system

Қарағанды университетінің хабаршысы. Математика сериясы, 2019
A mathematical model of root crops after cleaning and their movement pattern in a technological run for loading into means of transportation has been presented.
R.B. Hevko, I.G. Tkachenko, Y.B. Hlado, S.V. Synii, M.O. Gandziuk, O.M. Trokhaniak   +5 more
doaj   +1 more source

Air‐Pressure–Actuated Vibroacoustic Metamaterial With Tunable Bandgap: Design, Modeling, and Characterization

Advanced Engineering Materials, EarlyView.
This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal, Michael M. Becker, Sarah C. L. Fischer   +2 more
wiley   +1 more source

Performance Enhancement of Photovoltaic Solar Panels by a Cleaning Robot Technique

ITEGAM-JETIA
This paper presents a comprehensive approach to integrating Arduino with a current sensor, voltage sensor, two motors, and a motor driver to monitor the output of a solar panel and control a cleaning bot. Interacting the current and voltage sensors with
Pujari Harish Kumar, N Chinna Alluraiah, Swetha Shekarappa G, K Harinath Reddy, Keerthana M   +4 more
doaj   +1 more source

Cleaning ability of rotary NiTi systems with different kinematics

Bulletin of the National Research Centre, 2019
Background The aim of this study was to compare the cleaning ability of rotary NiTi systems with different kinematics: ProTaper Next (PTN) (continuous rotation motion), WaveOne Gold (WOG) (reciprocating motion), and Twisted File Adaptive (TFA) (adaptive ...
Amira Galal Ismail, Mohamed Mokhtar Nagy, Manar Galal   +2 more
doaj   +1 more source

Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger, Lienhard Wegewitz, Wolfgang Maus‐Friedrichs   +2 more
wiley   +1 more source

Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics

Advanced Engineering Materials, EarlyView.
Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost, Lionel Presmanes, Soléna Colin, Marie Vidal, Sophie Guillemet‐Fritsch   +4 more
wiley   +1 more source