Results 31 to 40 of about 16,569,160 (252)

Automation of Obtaining Parts Parameters for Tasks of Design-Technological Parametrization

open access: yesИнженерные технологии и системы, 2019
Introduction. Automation of obtaining design parameters of the part is the most important step in the integration of the design, process planning and manufacturing.
Alexander V. Shchekin
doaj   +1 more source

Investigation of thecontrol of the fat, oil and grease in sewer lines and their removal by surfactant treatment [PDF]

open access: yesAdvances in Environmental Technology, 2018
This study investigated different methodsof controlling the fat, oil and grease (FOG) in sewer systems. A comprehensive control program wasdevelopedfor the city of Mashhad (Iran) to maintain its sewer system and prevent blockages.
Majid Pirooz   +3 more
doaj   +1 more source

Estimating the Effect of a Bovine Viral Diarrhea Virus Control Program: An Empirical Study on the Performance of Dutch Dairy Herds

open access: yesFrontiers in Veterinary Science, 2022
More and more European countries have implemented a bovine viral diarrhea virus (BVDV) control program. The economic effects of such programs have been evaluated in simulations, but empirical studies are lacking, especially in the final stage of the ...
Xiaomei Yue   +4 more
doaj   +1 more source

Impact of Radiation Therapy on Physical and Psychosocial Health of Adolescents and Young Adults: A Joint Report From the Children's Oncology Group AYA and Radiation Oncology Committees

open access: yesPediatric Blood &Cancer, EarlyView.
ABSTRACT Rates of cancer among adolescents and young adults (AYA), age 15–39 years, are increasing. Consequently, radiation oncologists are treating more AYAs who have diagnoses spanning both pediatric and adult practices. Compared to pediatric and older adult patients, AYAs face a unique set of challenges.
Hesham Elhalawani   +7 more
wiley   +1 more source

A METHOD FOR SYNTHESIZING ABBREVIATED PROGRAMS FOR MONITORING THE TECHNICAL CONDITION OF ONBOARD EQUIPMENT OF A COMPLEX SYSTEM USING COMBINATORIAL OPTIMIZATION METHODS

open access: yesНадежность и качество сложных систем
Background . When testing onboard equipment of a complex system, one of the tasks to be solved is to monitor the technical condition to verify the correctness of its functioning. Requirements for reliability, efficiency and resource intensity are imposed
Andrey I. Loskutov   +3 more
doaj   +1 more source

Prevalence and distribution of Taeniasis and Cysticercosis

open access: yesMakara Journal of Health Research, 2016
Taenia saginata and Taenia solium are found through the whole world, especially in developing countries. These tapeworms live in the small intestines of humans. Cattle and pigs are the intermediate animal hosts. Serious signs and symptoms are found if T.
Widarso H.S Widarso   +3 more
doaj   +1 more source

Retrospective Analysis of Donor Lymphocyte Infusions in Pediatric Patients With Mixed Chimerism After Hematopoietic Stem Cell Transplantation

open access: yesPediatric Blood &Cancer, EarlyView.
ABSTRACT Background Allogeneic hematopoietic stem cell transplantation (alloHSCT) is an essential therapy for several malignant and nonmalignant diseases, but relapse and graft loss remain the principal threats to its success. Routine monitoring of chimerism and minimal residual disease (MRD) enables early detection of imminent recurrence and guides ...
Carmen Junk   +10 more
wiley   +1 more source

Dutch bovine viral diarrhea virus control program: Evaluation 2018–2023

open access: yesJournal of Dairy Science
: Since 2018, Dutch dairy farmers have been obliged to opt for 1 of 4 routes to achieve bovine viral diarrhea virus (BVDV) freedom in the national BVDV eradication program.
E.E.C. Strous   +8 more
doaj   +1 more source

Referral Patterns and Diagnostic Timeliness in Pediatric Cancer: A Hospital‐Based Study in Indonesia

open access: yesPediatric Blood &Cancer, EarlyView.
ABSTRACT Background Timely diagnosis and treatment are critical for improving survival among children with cancer. In low‐ and middle‐income countries (LMICs), delays are common and may be influenced by fragmented referral pathways and diagnostic limitations.
Nur Melani Sari   +5 more
wiley   +1 more source

CAD-CAM technologies for the design and manufacture of parts on CNC machines

open access: yesТехнічна інженерія, 2020
The paper investigates the use of CAD-CAM technologies for the design and manufacture of parts on machines with numerical program control (CNC). These technologies allow designing technological routes of processing of surfaces of details of various ...
O.A. Lytvynenko   +2 more
doaj   +1 more source

Home - About - Disclaimer - Privacy