Results 121 to 130 of about 1,809,136 (304)
Advanced Engineering Materials, Volume 27, Issue 6, March 2025.The stability criteria affecting the formation of high‐entropy alloys, particularly focusing in supersaturated solid solutions produced by mechanical alloying, are analyzed. Criteria based on Hume–Rothery rules are distinguished from those derived from thermodynamic relations. The formers are generally applicable to mechanically alloyed samples.
Javier S. Blázquez +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi +3 more
wiley +1 more source
The Electrochemical Commercial Vehicle (ECCV) Platform
EnergiesSeveral technological challenges delay the adoption of electrified powertrains in the heavy-duty transport sector. For fuel-cell hybrid electric trucks, key issues include slow cold start, reduced cooling power during high ambient temperatures, and ...
Max Johansson +7 more
doaj +1 more source
Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials
Advanced Engineering Materials, EarlyView.Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Energy Efficiency in Greenhouse Evaporative Cooling Techniques: Cooling Boxes versus Cellulose Pads [PDF]
, 2014 Evaporative cooling systems using a combination of evaporative pads and extractor fans require greenhouses to be hermetic. The greatest concentration of greenhouses in the world is located in southeast Spain, but these tend not to be hermetic structures ...
Franco Salas, Antonio +2 more
core +1 more source
Advanced Engineering Materials, EarlyView.This study examines how several molten high‐silicon electrical steels interact with both conventional and recycled MgO–C refractories. For this, various immersion experiments are conducted. In addition to infiltration, a number of mechanisms are identified and explained that control the corrosion of the refractory material.
Lukas Neubert +7 more
wiley +1 more source