Results 81 to 90 of about 394,878 (269)

Revisiting Stability Criteria in Ball‐Milled High‐Entropy Alloys: Do Hume–Rothery and Thermodynamic Rules Equally Apply?

Advanced Engineering Materials, Volume 27, Issue 6, March 2025.
The stability criteria affecting the formation of high‐entropy alloys, particularly focusing in supersaturated solid solutions produced by mechanical alloying, are analyzed. Criteria based on Hume–Rothery rules are distinguished from those derived from thermodynamic relations. The formers are generally applicable to mechanically alloyed samples.
Javier S. Blázquez, Alejandro F. Manchón‐Gordón, Antonio Vidal‐Crespo, Rafael Caballero‐Flores, Jhon J. Ipus, Clara F. Conde   +5 more
wiley   +1 more source

Analysis of the temperature evolution of the canned motor with spiral tube heat exchanger in secondary water supply blackout fault

Scientific Reports
In a canned motor with a spiral tube heat exchanger for a nuclear main pump, if the secondary water suddenly fails, the temperature of the lubricating water and motor winding insulation must not exceed the alarm or permitted value within the 5 min ...
Li-Kun Ai, Yi-Ping Lu
doaj   +1 more source

Optimization of heat sinks with plate fins in air-jet cooling

Nihon Kikai Gakkai ronbunshu, 2014
Heat density of high-load electronics such as high-performance servers and the inverters used in vehicles has been increasing as the result of higher processing speeds and computational scale, and higher output, etc.
Takayuki ATARASHI, Tetsuya TANAKA, Shigeyasu TSUBAKI   +2 more
doaj   +1 more source

Variable Stiffness Flexure Structures Enabled by Phase‐Change Gallium and Adhesive Interfacial Locking for Soft Robotic Applications

Advanced Engineering Materials, EarlyView.
A flexure‐based variable stiffness structure is developed by integrating phase‐change modulation and adhesive interfacial locking of gallium. The design enables a wide stiffness variability, transitioning from soft, flexible behavior to rigid, load‐supporting performance.
Sungjin Kim, Sohee John Yoon, Yong‐Lae Park   +2 more
wiley   +1 more source

Microstructural Evolution and Vacancy Defect Formation in Mn–Mo–Ni RPV Steel Under Low Cycle Fatigue: Insights From EBSD and PALS

Advanced Engineering Materials, EarlyView.
Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar, Dhanadeep Dutta, G. Bharat Reddy   +2 more
wiley   +1 more source

Thermodynamic Pathways of Nonequilibrium Solidification in Wire‐Arc Additive Manufacturing Fe‐Based Multicomponent Alloy Structures

Advanced Engineering Materials, EarlyView.
Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios, Anthony Gonzalez, Aleksander Aleman, Tyler Dolmetsch, Tanaji Paul, Arvind Agarwal   +5 more
wiley   +1 more source

The Electrochemical Commercial Vehicle (ECCV) Platform

Energies
Several technological challenges delay the adoption of electrified powertrains in the heavy-duty transport sector. For fuel-cell hybrid electric trucks, key issues include slow cold start, reduced cooling power during high ambient temperatures, and ...
Max Johansson, Arnaud Contet, Olof Erlandsson, Robin Holmbom, Erik Höckerdal, Oskar Lind Jonsson, Daniel Jung, Lars Eriksson   +7 more
doaj   +1 more source

Thermomechanical Fatigue and Creep–Fatigue Interaction of Inconel 718 Additively Manufactured by Laser Beam Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth, Tomáš Babinský, Jan Lars Riedel, Wen Hao Kan, Aijun Huang, Martin Heilmaier, Ivo Šulák   +6 more
wiley   +1 more source

Combined Process‐ and Phase‐Field‐Simulation to Predict the Microstructure of Single‐Crystal Ni‐Based Superalloys

Advanced Engineering Materials, EarlyView.
A combined finite element and phase‐field approach predicts the evolution of microstructure during the directional solidification of Ni‐based superalloys. The model reveals how withdrawal rate, temperature gradient, and wall thickness control the dendrite spacing, highlighting the strong effect of surface regions in thin sections where dendrite growth ...
Sean Böhm, André B. Baldissera, Rainer Völkl, Uwe Glatzel   +3 more
wiley   +1 more source

Low‐Angle Grain Boundaries and Re‐Segregation in Single‐Crystalline Ni‐Base Superalloys

Advanced Engineering Materials, EarlyView.
This work demonstrates that Re‐segregation at low‐angle grain boundaries (LAGBs) in Ni‐base superalloys is influenced by misorientation angle. Advanced microscopy and atom probe tomography reveal that higher misorientation angles increases Re‐segregation.
Alireza B. Parsa, Aparna Saksena, Alesander Kostka, Pascal Thome, Felicitas Scholz, Alexandre Mussi, Christoph Somsen, Baptiste Gault, Jan Frenzel, Gunther Eggeler   +9 more
wiley   +1 more source