Results 101 to 110 of about 800,553 (303)
Advanced Engineering Materials, EarlyView.This study presents a reversible temperature sensor with high switching ratio, ∼103. The device is fabricated using PET‐ITO and carbon nanotube dispersions in alkane. Considering its application in cold chain logistics, a proof‐of‐concept with LED is showcased. Thus, a temperature drop below the threshold temperature (crystallization temperature of the
Sunil Kumar Behera +8 more
wiley +1 more source
Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials
Advanced Engineering Materials, EarlyView.Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo +3 more
wiley +1 more source
Energies, 2018 This paper presents a comparative study of the cross-flow regenerative heat and mass exchanger (HMX) and the conventional cross-flow HMX for indirect evaporative cooling (IEC) with numerical methods.
Yugang Wang, Xiang Huang, Li Li
doaj +1 more source
Investigation of film cooling effectiveness and enhancement of cooling performance
, 2018 Advanced gas turbines are designed to operate at increasingly higher inlet temperatures to increase efficiency and specific power output. This increase in the operating temperature is enabled by advances in high-temperature resistant materials such as super alloys and thermal-barrier coatings (TBCs) and by the development of effective cooling methods ...
openaire +3 more sources
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source
Simulation and Comparison of Cooling Performances of Refrigerated Vehicles with Different Structures
Zhileng xuebao, 2018 The reasonable optimization and improvement of the structure of the refrigerated compartment plays an important role in efficiently improving the cooling effect of a refrigerated truck, which ensures the quality and safety of the goods during ...
Zhang Xiang +6 more
doaj
The CF6 Jet Engine Performance Improvement - Low Pressure Turbine Active Clearance Control [PDF]
A low pressure turbine (LPT) active clearance control (ACC) cooling system was developed to reduce the fuel consumption of current CF6-50 turbofan engines for wide bodied commercial aircraft. The program performance improvement goal of 0.3% delta sfc was
Beck, B. D., Fasching, W. A.
core +1 more source
Three-dimensional simulation of a new cooling strategy for proton exchange membrane fuel cell stack using a non-isothermal multiphase model [PDF]
, 2019 In this study, a new cooling strategy for a proton exchange membrane (PEM) fuel cell stack is investigated using a three-dimensional (3D) multiphase non-isothermal model.
Jiao, K, Wang, Y, Yuan, H, Zhang, G
core