Results 221 to 230 of about 1,073,601 (348)

Impact of Structural Adhesive Hybridization Strategy on the Performance of In‐Mold Electronics Devices Across Thermoforming and Injection Molding

Advanced Engineering Materials, EarlyView.
In‐mold electronics (IME) undergo complex thermoforming and over‐molding processes that strain device integrity. This study demonstrates how adapting the amount and placement of structural adhesive to local deformation levels preserves electrical functionality.
Francisco Ituriel Arias‐García, Nekane Lozano‐Hernandez, Maria Lluisa Maspoch, Enric Fontdecaba   +3 more
wiley   +1 more source

Effect of Cooling Rate on α Variant Selection and Microstructure Evolution in TB17 Titanium Alloy. [PDF]

Materials (Basel)
Shang G, Gan X, Wang X, Ge J, Li C, Zhu Z, Zhang X, Zhou K.   +7 more
europepmc   +1 more source

Low-cooling-rate freezing in biomolecular cryo-electron microscopy for recovery of initial frames. [PDF]

QRB Discov, 2021
Wu C, Shi H, Zhu D, Fan K, Zhang X.
europepmc   +1 more source

Coefficient of normal restitution of viscous particles and cooling rate of granular gases [PDF]

, 1998
Thomas Schwager, Thorsten Pöschel
openalex   +1 more source

Surface Modification of Fluorine‐Free Superhydrophobic Materials with (Ultra‐)Thin TiO2 Layers

Advanced Engineering Materials, EarlyView.
Significant changes in wettability, with a reduction of 60o in the water conduct angle, are reported via the surface modification of fluorine‐free superhydrophobic thin films, prepared by aerosol‐assisted chemical vapor deposition, after coating a 4 nm layer of titanium dioxide on the surface using atomic layer deposition.
Julie Jalila Kalmoni, Chris Blackman, Claire J Carmalt   +2 more
wiley   +1 more source

Critical Cooling Rate of Fast-Crystallizing Polyesters: The Example of Poly(alkylene trans-1,4-cyclohexanedicarboxylate). [PDF]

Polymers (Basel)
Hallavant K, Soccio M, Guidotti G, Lotti N, Esposito A, Saiter-Fourcin A.   +5 more
europepmc   +1 more source

Ocular surface cooling rate associated with tear film characteristics and the maximum interblink period. [PDF]

Sci Rep, 2021
Ding JE, Kim YH, Yi SM, Graham AD, Li W, Lin MC.   +5 more
europepmc   +1 more source

Variations of Solidified structure by changing the cooling rates in the eutectic composition of Al-Si alloy

, 1970
Yo Serita, Toshio Ishikawa, Fujio Kimura
openalex   +2 more sources

Induction of rapid cold hardening by cooling at ecologically relevant rates in Drosophila melanogaster [PDF]

, 1999
Jonathan D Kelty, Richard Lee
openalex   +1 more source

Ultrasonic Atomization Spray Coating of PCL on an Mg‐Based Alloy Enhanced by Plasma Electrolytic Oxidation for Improved Adhesion, Corrosion Resistance, and Biocompatibility

Advanced Engineering Materials, EarlyView.
Plasma electrolytic oxidation is combined with ultrasonic spray deposition of polycaprolactone (PCL) on WE43 magnesium alloy to improve adhesion, corrosion resistance, and cytocompatibility. The hybrid coating demonstrates significantly reduced hydrogen evolution and enhances mechanical bonding, offering a promising strategy for next‐generation ...
Seyed Masih Mousavizadeh, Atiyeh Adelinia, Frederick D. Crowley, Jamal Seyyed Monfared Zanjani, John J. E. Mulvihill, Mingzhi Yu, Ehsan Rezvani, Matthijn de Rooij, Michael D. Gilchrist, Nan Zhang   +9 more
wiley   +1 more source