Results 1 to 10 of about 504,332 (309)

Estimate of cooling rate of melts based on non-ferrous metals. [PDF]

Металознавство та обробка металів, 2019
The method of studying the rate of cooling of the melt on the example of a Cu-Zn alloy is presented.
Verkhovliuk M. , Lakhnenko V. L. , Petrovsky R. V. , Chervony I. F.   +3 more
doaj   +1 more source

Electrolytic coating of iron-chromium alloy of sulphate-chloride electrolyte in machine parts recovery process modelling

Вестник СибАДИ, 2023
Introduction. The technological process of restoring a part should provide more than 80% of the resource and no more than 50% of the cost of a new part.
A. S. Lanuta, Yu. V. Shtefan, V. К. Fiodorov, N. I. Korneichuk   +3 more
doaj   +1 more source

Alloying Motif Confined in Intercalative Frameworks toward Rapid Li‐Ion Storage

Advanced Science, 2022
High‐capacity alloying‐type anodes suffer poor rate capability due to their great volume expansion, while high‐rate intercalation‐type anodes are troubled with low theoretical capacity.
Xueyu Lin, Chenlong Dong, Siwei Zhao, Baixin Peng, Ce Zhou, Ruiqi Wang, Fuqiang Huang   +6 more
doaj   +1 more source

Study of Adsorption of Hydrogen on Al, Cu, Mg, Ti Surfaces in Al Alloy Melt via First Principles Calculation

Metals, 2017
Adsorption of hydrogen on Al(111), Cu(111), Mg(0001), and Ti(0001) surfaces have been investigated by means of first principles calculation. The calculation of surface energy indicates that Mg(0001) is the most stable surface, while Ti(0001) is the most ...
Yu Liu, Yuanchun Huang, Zhengbing Xiao, Xianwei Reng   +3 more
doaj   +1 more source

Insight in the properties of WO3|Y: A first-principle study

Results in Physics, 2019
In this paper, the properties of WO3|Y when yttrium atoms are adsorbed on the surface of WO3 are studied systematically using first-principles calculations.
Xieyi Zhang, Xianwei Ren, Zhengbing Xiao, Yuanchun Huang   +3 more
doaj   +1 more source

Effect of Heating Rate on Creep Aging Behavior of 2219 Aluminum Alloy

Cailiao gongcheng, 2018
Effect of heating rate on creep aging behavior and mechanical properties in the process of creep aging forming of 2219 aluminum alloy was studied. In order to simulate the temperature conditions of the component in autoclave, heating rate was reduced to ...
LIU Ling-feng, ZHAN Li-hua, LI Wen-ke
doaj   +1 more source

The effect of room temperature pre-ageing on tensile and electrical properties of thermomechanically treated Al-Mg-Si alloy [PDF]

Journal of Mining and Metallurgy. Section B: Metallurgy, 2002
A commercial Al - 0.62%Mg - 0.57%Si was thermomechanically treated (TMT). The TMT process included solution treatment, room temperature preageing, drawing (e=95%) and final ageing.
Martinova Z., Damgaliev D., Hirsh M.
doaj   +1 more source

Modeling and Simulation of the Static Recrystallization of 5754 Aluminium Alloy by Cellular Automaton

Metals, 2018
To study the factors that affect the mechanical properties of materials, double-pass hot compression tests were performed under different deformation parameters using a Gleeble-3500 thermo-simulation machine.
Changqing Huang, Xiaodong Jia, Zhiwu Zhang   +2 more
doaj   +1 more source

AFLOW for Alloys

Journal of Phase Equilibria and Diffusion
Small AFLOW review submitted to special issue.
Toher, Cormac, Curtarolo, Stefano
openaire   +2 more sources

Development and application analysis of ceramic composites armor for helicopter

Journal of Aeronautical Materials, 2019
At present，lightweight armour has been fitted in foreign military helicopters for gunships and transport. By contrast，the armor configuration of domestic helicopters is still a big gap compared with Europe and America in the level type，quantity and ...
WU Yue, WANG Xudong, LIU Di, LI Jiongli, GUO Jianqiang, LI Wenbo, ZHANG Haiping, CAO Zhen   +7 more
doaj   +1 more source