Results 31 to 40 of about 423,347 (319)
Simulating the galvanic coupling between S-Al2CuMg phase particles and the matrix of 2024 aerospace aluminium alloy [PDF]
, 2012 Study of the corrosion behaviour of a magnetron sputtered Al–Cu/Al–Cu–Mg model alloy couple in sulphate solutions has been undertaken to gain insight into the galvanic coupling between the matrix and SAl2CuMg particles in the 2024 aluminium alloy (AA2024)
Blanc, Christine +11 more
core +1 more source
Hardness and Conductivity of Die Forged ZYK530 Magnesium Alloy
Medžiagotyra, 2022 The relationship among the microstructure, hardness and electrical conductivity of the as-forged ZYK530 Mg alloy after heat treatment was analyzed and studied using a microscope, X-Ray Diffractometer, eddy current conductivity meter, and Vickers ...
Fenghong CAO +4 more
doaj +1 more source
Metals, 2020 In this study, the continuous evolution of the second-phase particles across as-cast, homogenization, multi-directional forging (MDF), and solution-aging treatment and their effect on tensile fracture behavior of 2219 aluminum alloys with different Cu ...
Daofen Xu +3 more
doaj +1 more source
Excimer laser treatment of ZE41 magnesium alloy for corrosion resistance and microhardness improvement [PDF]
, 2010 We would like to acknowledge the financial support of the ‘‘Conseil regional de PACA’’ and Protection des Metaux d’Arenc). The authors are grateful to PMA’s engineers Ms. E. Castellan, Ms. A. Gonthier and Mr. F.
KHALFAOUI, Walid +3 more
core +1 more source
Metals, 2019 In this study, castings of TiC nanoparticle reinforced 2219 aluminum matrix composites with different TiC nanoparticle contents (0, 0.5, 0.9, 1.3, and 1.7 wt.%) prepared using an ultrasound-assisted stirring technology were deformed by multidirectional ...
Yilong Yang +4 more
doaj +1 more source
Potential fatigue strength improvement of AA 5083-H111 notched parts by wire brush hammering: Experimental analysis and numerical simulation [PDF]
, 2014 The effects of milling as machining process and a post-machining treatment by wire-brush hammering, on the near surface layer characteristics of AA 5083-H111 were investigated.
SIDHOM, Habib +4 more
core +1 more source
Influence of oxide films on primary water stress corrosion cracking initiation of alloy 600 [PDF]
, 2006 In the present study alloy 600 was tested in simulated pressurised water reactor (PWR) primary water, at 360 °C, under an hydrogen partial pressure of 30 kPa. These testing conditions correspond to the maximum sensitivity of alloy 600 to crack initiation.
Panter, J. +6 more
core +1 more source
Metals, 2022 To understand the effect of the initial state of AA2195 Al-Li alloy on the forming process, as-cast and homogenized ingots were compressed by using a Gleeble-3150 thermo-mechanical simulator at different temperatures (360–480 °C) and strain rates (0.01 ...
Jin Zhang, Zemeng Liu, Dongfeng Shi
doaj +1 more source
Process Mechanics and Surface Integrity Induced by Dry and Cryogenic Machining of AZ31B-O Magnesium Alloy [PDF]
, 2013 The corrosion resistance of magnesium alloys depends mainly on its surface integrity. Previous experimental studies have shown that machining can induces small (nano-scale) grain size, compressive residual stresses and basal plane crystallographic ...
Fromentin, G. +18 more
core +1 more source
A predictive fatigue life model for anodized 7050 aluminium alloy [PDF]
, 2013 The objective of this study is to predict fatigue life of anodized 7050 aluminum alloy specimens. In the case of anodized 7050-T7451 alloy, fractographic observations of fatigue tested specimens showed that pickling pits were the predominant sites for ...
Chaussumier, Michel +4 more
core +1 more source