A predictive fatigue life model for anodized 7050 aluminium alloy [PDF]
, 2013 The objective of this study is to predict fatigue life of anodized 7050 aluminum alloy specimens. In the case of anodized 7050-T7451 alloy, fractographic observations of fatigue tested specimens showed that pickling pits were the predominant sites for ...
Chaussumier, Michel +4 more
core +1 more source
Review of Creep Cavitation and Rupture of Low Cr Alloy and its Weldment [PDF]
, 2013 This paper presents a review of creep cavitation and rupture of low Cr alloy and its weldment, particular in the heat-affected zone (HAZ). Creep damage is one of the serious problems for the high temperature industry.
Xu, Qiang +6 more
core +1 more source
Grain refinement efficiency of a new oxide-containing master alloy for aluminium casting alloys [PDF]
, 2014 In this study, grain refinement efficiency of a new oxide master alloy based on MgAl2O4 was demonstrated on an A357 alloy. The grain size of the reference alloy was reduced by 50-60% with the addition of the master alloy and introduction of ultrasonic ...
Dmitry G. Eskin +7 more
core +1 more source
Effect of tension on edge crack of on-line heating rolled AZ31B magnesium alloy sheet
Journal of Materials Research and Technology, 2020 Edge crack is a common defect in the rolled magnesium alloy sheet which increase the rolling cost. In this study, the effect of tension on the edge crack of AZ31B sheet rolled with on-line heating rolling was investigated.
Yuchen Huang +6 more
doaj +1 more source
Texture Evolution of AZ31 Magnesium Alloy Sheet at High Strain Rates [PDF]
, 2010 In the current contribution the mechanical behaviour at high strain rates of AZ31 magnesium alloy sheet is studied. Uniaxial deformation properties were studied by means of tensile split Hopkinson pressure bar (SHPB) at different temperatures.
Hurtado, I. +9 more
core +1 more source
Discovery and engineering of bispecific TCR-mimic antibodies targeting peptide–HLA complex
mAbsTCR-mimic (TCRm) antibodies represent a promising new frontier in cancer immunotherapy, enabling the targeting of intracellular targets previously considered undruggable with antibodies. We developed an integrated platform for generating human antibodies
Jennifer Watkins-Yoon +16 more
doaj +1 more source
Modelling of security properties in Alloy [PDF]
, 2011 We study the problem of verification of securityproperties of Session Initiation Protocol (SIP) using the modelanalyser Alloy. We propose a novel approach to model analysisand demonstrating robustness of protocol models in first ...
Georgieva, Lilia, L. Georgieva
core +1 more source
A Novel Rolling Bearing Fault Diagnosis Method Based on Adaptive Feature Selection and Clustering
IEEE Access, 2021 Rolling bearing is an important part of mechanical equipment. Timely detection of rolling bearing fault is one of the important factors to ensure the safe operation of equipment.
Jingbao Hou +4 more
doaj +1 more source
Lubricated sliding wear behaviour of aluminium alloy composites
, 2005 Interest in aluminium alloy (Al-alloy) composites as wear resistant materials continues to grow. However, the use of the popular Al-alloy-SiC composite can be limited by the abrasive nature of the SiC, leading to increased counterface wear rates.
Rainforth, W.M., Jones, H., Walker, J.C.
core +1 more source
Combined Kelvin probe force microscopy and secondary ion mass spectrometry for hydrogen detection in corroded 2024 aluminium alloy [PDF]
, 2013 The capability of Kelvin probe force microscopy (KFM) to detect and locate hydrogen in corroded 2024 aluminium alloy was demonstrated. Hydrogen was introduced inside the 2024 alloy following a cyclic corrosion test consisting of cycles of immersion in 1 ...
Blanc, Christine +5 more
core +1 more source