Results 21 to 30 of about 504,332 (309)
Constitutive model and hot workability of 2195 Al-Li alloy based on stress correction
Journal of Aeronautical Materials, 2021 The isothermal compression tests of 2195 Al-Li alloy annealed at 400 - 490 ā and strain rate 0.01-10sā1 were carried out. The true stress-strain curve obtained from the experiment was modified by friction force and temperature rise effects, and the ...
ZHAO Yifan +3 more
doaj +1 more source
Applied Sciences, 2023 In this study, single point incremental forming (SPIF) of Al-Li alloy sheets under different forming angles are studied via both experimental methods and numerical simulations.
Zibo Tang +3 more
doaj +1 more source
Applied Sciences, 2021 The preparation of the Al-Zn-Mg-Cu T-type rib consisted of forging, quenching, cold pressing, aging and the final machining processes, and the evolution of residual stress played a significant role in its properties and accuracy.
Yaoqiong Liu +3 more
doaj +1 more source
Study on Residual Stresses of 2219 Aluminum Alloy with TIG Welding and Its Reduction by Shot Peening
Metals, 2023 Large residual stress of 2219 aluminum alloy induced by Tungsten Inert Gas (TIG) welding decreases its service performances. Shot peening was adopted to decrease the residual stress of TIG welding.
Tao Zhang +3 more
doaj +1 more source
Assessment of wear resistance of tin and tin alloy coatings [PDF]
, 2007 This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.Tin alloy coatings have traditionally been used as corrosion resistant bamens due to their inert nature and comprehensive coverage, and have seldom been ...
Lam, Wayne Pui-Wing
core +7 more sources
Friction behavior of laser cladding magnesium alloy against AISI 52100 steel [PDF]
, 2012 The use of magnesium alloys in engineering applications is becoming increasingly important as a relatively low density allows savings in energy consumption and therefore reduction in air pollution.
J.E. Masse +3 more
core +1 more source
Improvement of the Corrosion Resistance by Addition of Ni in Lean Duplex Stainless Steels
Metals, 2020 On newly developed Febalance-18Cr-7Mn-3Mo-3W-0.4N-(0.03, 0.57)Ni (in wt%) lean duplex stainless steels, the microstructure, element partitioning behavior, and resistance to pitting corrosion were investigated.
Heon-Young Ha +4 more
doaj +1 more source
Microstructure and properties of welds between 5754 Al alloys and AZ31 Mg alloys using a Yb:YAG laser [PDF]
, 2014 The authors wish to thank Mr. Henri ANDRZEJEWSKI for his technical assistance in laser experiments. The authors wish to place their sincere thanks to Professor Philippe BOURNOT and Dr.
BANNOUR, Sana +9 more
core +1 more source
Effect of trace germanium on microstructure and quenching sensitivity of 7056 aluminum alloy
Cailiao gongcheng, 2019 The effect of trace Ge on the microstructure and quenching sensitivity of 7056 aluminum alloy was studied by mechanical tensile and end quenching experiments, combined with some analysis methods such as metallographic observation, hardness test ...
LI Wei +5 more
doaj +1 more source
Effect of Cu on the Fracture and Exfoliation Corrosion Behavior of Al-Zn-Mg-xCu Alloy
Metals, 2018 In the present work, the influence of Cu content on microstructure, mechanical properties and exfoliation corrosion behaviors of Al-Zn-Mg-xCu alloy extrusions has been investigated in longitudinal-transverse (L-T) and short-longitudinal (S-L) directions ...
Huibin Jiao +5 more
doaj +1 more source