Results 131 to 140 of about 1,952,754 (311)
Effect of Ni/Sn ratio on microstructure and properties of Cu-Ni-Sn-P alloy
Scientific ReportsCu-1.33Ni-1.35Sn-0.08P(Ni/Sn = 1/1), Cu-0.87Ni-1.82Sn-0.08P (Ni/Sn = 1/2) and Cu-1.78Ni-0.86Sn-0.08P (Ni/Sn = 2/1) alloys were prepared to explore the effect of different Ni/Sn ratios on the microstructure and properties of the alloys. The results showed
Xiaokang Chen +4 more
doaj +1 more source
Journal of Materials Research and TechnologyIn this study, Cu-3.44Ni-0.86Si-xSn (x = 0, 1, 2 wt%) alloy strips were fabricated via two different processing routes, namely the traditional preparation (TP) process and the improved preparation (IP) process.
Jiahao Wang +9 more
doaj +1 more source
Influence of copper on the electronic properties of amorphous chalcogenides
, 2005 We have studied the influence of alloying copper with amorphous arsenic sulfide on the electronic properties of this material. In our computer-generated models, copper is found in two-fold near-linear and four-fold square-planar configurations, which ...
A. Zakery +8 more
core +1 more source
Thermophysical Properties of the Desulphurization Slags With Various CaS and CaO/Al2O3 Ratio
Advanced Engineering Materials, EarlyView.This article investigates how CaS content and the CaO/Al2O3 ratio influence the thermophysical properties of desulphurization slags. Using experimental measurements and thermodynamic simulations, this study reveals complex effects on viscosity, surface tension, and density, providing new insight into slag structure and phase behavior under ...
Eldar Salpagarov +4 more
wiley +1 more source
Reducing russeting of organically grown Elstar to increase quality [PDF]
, 2008 Sales organisations indicated that opportunities for organic apples sales can increase when quality increases, in particular reducing the amount of russeting. The use of copper is probably the most important factor for russeting.
Jong, P.F., van der Maas, M. P.
core
Advanced Engineering Materials, EarlyView.ZnS‐MXene‐TiO2 nanocomposite heterojunction for photocatalytic decomposition of this methylene blue dye (MB) greatly improves light absorption, charge separation, and active site area. Two‐dimensional MXene forms nanocomposites by easily combining them with 0D (quantum dots), 1D (tube and wire), 2D (plane and sheet), and 3D (particle and lamellar ...
Latiful Kabir +7 more
wiley +1 more source
Advances in Mechanical EngineeringIn practical industrial applications, the operating conditions of bearings frequently change, posing significant challenges for reliable fault diagnosis.
Lulu Wang +3 more
doaj +1 more source
Study of crevice-galvanic corrosion of aluminum [PDF]
, 1967 Corrosion effects of aluminum-copper and aluminum-nickel couples in oxygenated distilled water, and aluminum alloys in oxygenated copper sulfate solution were studied. One of each of the couples had a water tight seal, and showed no substantial corrosion,
Draley, J. E., Loess, R. E., Mori, S.
core +1 more source
Advanced Engineering Materials, EarlyView.Carbon‐free inert anodes are essential for decarbonizing aluminum electrolysis. This study investigates a recyclate‐based MgO‐316L steel composite anode tested under galvanostatic Hall–Héroult conditions in cryolite at 1000°C. Microstructural analysis reveals selective MgO fluorination, spinel and oxide layer formation, electrolyte infiltration, and ...
Serhii Yaroshevskyi +7 more
wiley +1 more source
Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger +2 more
wiley +1 more source