Results 1 to 10 of about 148,672 (304)
Study on the Bacterial Communities of the Biofilms on Titanium, Aluminum, and Copper Alloys at 5,772 m Undersea in Yap Trench [PDF]
Frontiers in Microbiology, 2022 Biofilms formed on metal surfaces strongly affect metallic instruments serving in marine environments. However, due to sampling difficulty, less has been known about the bacterial communities of the biofilm on metallic surfaces in hadal environments, so ...
Xiaofan Zhai +13 more
doaj +2 more sources
Antimicrobial effect of copper alloys on Acinetobacter species isolated from infections and hospital environment [PDF]
Antimicrobial Resistance and Infection Control, 2018 Background An increased proportion of Gram-negative bacteria have recently been reported among etiologic agents of infection. In Poland, Acinetobacter baumannii is a big problem for hospitals, especially intensive care units.
Anna Różańska +4 more
doaj +2 more sources
Applied Sciences, 2023 Advanced digital solutions are increasingly introduced into manufacturing systems to make them more intelligent. Intelligent Waste Management Systems in industries allow for data collection and analysis to make better-informed decisions, monitor and ...
Kosmas Alexopoulos +7 more
doaj +1 more source
Research Status of Laser Cladding Technology on the Surface of Copper Alloy [PDF]
Cailiao Baohu, 2022 Laser cladding has the characteristics of high energy density, small heat - affected zone, metallurgical bonding between the cladding layer and the substrate, compact cladding layer structure, fine grains and excellent performance.
YANG Jie, HE Chunlin, SUN Yuhaixuan, CHI Pingjiao, YANG Xipeng, YU Jihao, SONG Guihong
doaj +1 more source
Anneal hardening effect in sintered copper alloys [PDF]
Science of Sintering, 2002 Samples of copper and copper alloys CuNi and CuNiAl were prepared by a powder metallurgical method and were then subjected to cold rolling with different degrees of deformation. Copper and copper alloys in the cold-rolled state were isochronally annealed
Nestorović Svetlana +2 more
doaj +1 more source
The effect of zinc on the microstructure and phase transformations of casting Al-Cu alloys [PDF]
Tehnika, 2016 Copper is one of the main alloying elements for aluminum casting alloys. As an alloying element, copper significantly increases the tensile strength and toughness of alloys based on aluminum.
Manasijević Ivana I. +5 more
doaj +1 more source
Studying the Effect of Adding Up To 6wt%Cu on Some Mechanical and Physical Properties of Pure Aluminum [PDF]
Kirkuk Journal of Science, 2016 Aluminum and its alloys solidify in columnar structure with large grain size which results in deterioration of their surface quality and strength. Aluminum alloys with a wide range of properties are used in engineering structures.
Nawzad J. Mahmood +2 more
doaj +1 more source
Shape Memory Behavior of Rapidly Quenched High-copper TiNiCu Alloys
U.Porto Journal of Engineering, 2021 Rapidly quenched quasibinary TiNi–TiCu system alloys with high copper contents (above 20 at.%) exhibit excellent shape memory effect and have considerably narrower hysteresis as compared with the TiNi binary alloy, this advantage being of special ...
Alexander Shelyakov +4 more
doaj +1 more source
Materials & Design, 2023 The mechanism for enhanced precipitation strengthening due to the addition of copper to Al-9.0Zn-1.5Mg (wt.%) alloys has been investigated by means of tensile test, transmission electron microscopy, anomalous small-angle X-ray scattering and three ...
Mengchu Yang +4 more
doaj +1 more source
Весці Нацыянальнай акадэміі навук Беларусі: Серыя фізіка-тэхнічных навук, 2022 The influence of the regimes of plastic deformation of steel – copper alloy pseudo-alloys obtained by infiltration on their structure, mechanical properties and anisotropy of properties is investigated.
L. N. Dyachkova
doaj +1 more source